Bosch B450 Especificaciones descargar pdf (Pagina 2)

Bosch Security Systems, Inc.

130 Perinton Parkway

Fairport, NY 14450

USA

www.boschsecurity.com

Bosch Sicherheitssysteme GmbH

Robert-Bosch-Ring 5

85630 Grasbrunn

Germany

This document is the intellectual property of Bosch Security

Trademarks

All hardware and software product names used in this document

are likely to be registered trademarks and must be treated

accordingly.

Bosch Security Systems, Inc. product manufacturing dates

Use the serial number located on the product label and refer to

the Bosch Security Systems, Inc. website at

http://www.boschsecurity.com/datecodes/.

6 | Show the rmware version

Table 5.2: RX/TX LEDs Description

Flash pattern Function

RX (Receive) Flashing Occurs when the module

receives a message from

over-the-air.

TX (Transmit) Flashing Occurs when the module

receives a message to send

out over-the-air.

4.4 |

Conguring with USB

The B450 supports conguration by USB. Before you can access

the USB interface, you must install the RBUS1CP.inf le on the

target PC or laptop. The RBUS1CP.inf le is available on the

supplied CD-ROM.

NOTICE!

Power up the B450 with the address switch set

to the desired bus. When ready to program using

USB, turn the switch to position 0. When done

programming, turn the switch back. Failure to return

the address switch to the previous setting will result

in a trouble condition.

4.4.1 |

Install a communication program

To use USB connection from a computer to the B450 to

congure the B450, you must use a terminal emulator software

program such as Tera Term, located on the included B450 CD-

ROM.

NOTICE!

USB connection via the USB cable is only used for

temporary conguration programming.

4.4.2 |

Connect via USB cable

Insert one end of the USB cable into the PC or laptop, and insert

the other end into the B450 USB port.

4.4.3 |

Log into USB interface

Log into the USB interface and make your selections. For more

information, refer to the B450 Installation and Operation Guide.

5 |

LED descriptions

The B450 Module includes the following on-board LEDs to

assist with troubleshooting issues (refer to Figure 1.1 for the

location of the LEDs):

– Heartbeat (system status). Refer to Table 5.1.

– RX/TX communication. Refer to Table 5.2

To review the rmware version using an LED ash pattern,

tamper the B450.

Refer to Section 5 for ash patterns.

To tamper the B450, do one of the following:

– If the optional tamper switch is installed:

With the enclosure door open, close the tamper

switch.

– If the optional tamper switch is NOT installed:

Momentarily short the tamper pins (use a jumper or

screwdriver).

When the tamper switch is activated (open to closed), the

heartbeat LED stays OFF for 3 sec before indicating the

rmware version. The LED pulses the major, minor, and micro

digits of the rmware version, with a 1 sec pause after each

digit. The following is an example: The version 1.4.3 would be

shown as LED ashes:

Figure 6.1: Firmware LED ash patterns example

[3 second pause] *___****___*** [3 second pause, then

normal operation].

7 |

Certications

8 |

Specications

Dimensions

(HxWxD)

79 mm x 128 mm x 38 mm (3.11 in x 5.03 in x 1.50 in)

Voltage

(Operating)

12 VDC nominal

Current

(Maximum)

Standby: B450 with B440/B441/B442/B443 = 75mA

Alarm: B450 with B440/B441/B442/B443 = 180 mA

USB cable USB cable (Type A to A male-to-male) - not supplied It is

recommended to use Bosch cable B99 (F01U278853)

Data bus wire size 2 mm to 0.65 mm (12 AWG to 22 AWG)

Data bus wire

length

Maximum Distance

– wire size: 22 AWG (0.65 mm) --> 12 m (40 ft)

18 AWG (1.0 mm) --> 30 m (100 ft)

16 AWG (1.3 mm) --> 48 m (158 ft)

12 AWG (2.0 mm) --> 122 m (400 ft)

Using a separate UL listed power supply, such as the

B520 Auxiliary Power Supply Module, connected to the

B450 within the specication listed above, the wire

distance can be extended up to 300 m (1000 ft)

Compatibility B5512/B4512/B3512 control panel

D9412GV4/D7412GV4 (v1.00.oxx and up) control panel

D9412GV3/D7412GV3/D7212GV3 control panel

D9412GV2/D7412GV2/D7212GV2 control panel v7.06+

FPD-7024 (v1.03 and higher) control panel

AMAX 2000/2100/3000/4000 control panel

CMS 6/8/40 control panel

Solution 2000/3000

Easy Series v3+

B10 enclosure

B11 enclosure

D8103 enclosure

D203 enclosure

Relative humidity Up to 93% non-condensing

Temperature

(operating)

0° to +49° C (+32° to 120° F)

Temporary loss of communication may be caused by static when using any-

one of the above enclosures.

Installed Bus

Function Option/SDI SDI2 Details

IP Event Report-

ing

Y Y TCP protocols only sup-

ported on SDI2

Remote Program

(RPS or A-link)

Y Y Requires Bosch Cellular

service or other cellular

network access

Congure B450

from panel

(RPS, A-link)

N Y GV4/B Series v2.03+

Personal Noti-

cation via SMS

or Email

N Y Requires compatible con-

trol panel and cellular plan

Remote Security

Control App

N Y Requires Bosch Cellular

service or other cellular

network access

8.1 |

B450 cellular interface compatibility

Use the following table for cellular interface compatibilities.

NOTICE!

When the tamper is shorted, the rmware version

ashes, then the B450 LEDs are disabled to conserve

power. To see the troubleshooting LEDs, open the

tamper circuit or jumper.

Region Certication

FCC Part 15 Class B

NIST FIPS 197 AES Certication (IP Communications)

UL 365 – Police Station Connected Burglar Alarm Units and

Systems

UL 636 – Hold Up Alarm Units and Systems

UL 864 – Control Units and Accessories for Fire Alarm Systems

UL 985 – Household Fire Warning System Units

UL 1023 – Household Burglar Alarm System Units

UL 1076 – Proprietary Burglar Alarm Units and Systems

UL 1610 – Central Station Burglar Alarm Units

SIA CP-01:2010 False Alarm Reduction

California State Fire Marshall (CSFM)

Fire Department of New York (FDNY) Certied

Canada

CAN/ULC S303 - Local Burglar Alarm Units and Systems

CAN/ULC S304 - Signal Receiving Centre and Premise Alarm

Control Units

ULC - S545 - Residential Fire Warning System Control Units

ULC-ORD C1023 - Household Burglar Alarm System Units

ULC-ORD C1076 - Proprietary Burglar Alarm Units and

Systems

ICES-003 - Digital Apparatus

Europe

CE - EMC Directive 2004/108/EC

Australia

A-Tick - Certied

Flash pattern Function

Flashes once every 1 sec Normal State: Indicates

normal operation state.

3 quick ashes every 1 sec Communication Error

State: Indicates a bus

communication error with

the control panel.

On Steady Trouble State: Indicates a

trouble condition exists.

Examine the other LEDs

to determine the trouble

condition.

Off LED Trouble State: Module

is not powered, or there is a

failure in the module. Check

for proper installation.

Table 5.1: Heartbeat LED Descriptions

en Quick Start Guide

Conettix Plug-in Communicator Interface

B450

1 2

Callout ― Description 1

Comentarios a estos manuales

Sin comentarios

Bosch B450 Especificaciones Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch B450