Bosch 150 AC Especificaciones Pagina 101
- Pagina / 146
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
101
• DOK-DIAX01-MAIN+2AD+1M-ANW1-EN-E1,44 • 07.97
4. Diagnostics and Fault Clearance
Cause:
No EEPROM (IC3) in the programming module, or the existing EEPROM
is faulty.
Remedy:
Switch control unit off. Insert EEPROM inito programming module, or
replace faulty EEPROM. Contact Indramat customer service!
Cause:
• Wrong value in FEEDBACK (M03) parameter. This type of motor
feedback requires a different parameter value.
• Faulty or wrong feedback cable.
Remedy:
• Set parameter value in M03 which suits the type of motor feedback.
• Repair or replace feedback cable.
Note: see Section 5.3
Cause:
The gear box cannot be engaged or the reduction stage acknowledgment
signal is faulty.
Remedy:
Switch the control unit off. Examine contactor wiring and acknowledgement
contacts. Check correct operation of change gear.
Note: see Section 3.15.1
Cause:
• No spindle reference signal at EXT POS control input (X2/37).
• No spindle or motor feedack zero pulse.
Remedy:
• Check correct connections and closing angle of spindle reference
switch!
• Check feedback leads!
Note: see Section 3.6
Cause:
The heatsink of the control unit has overheated. The TEMPWARN signal
(X2/9) was ignored. The control unit has shut down.
Remedy:
Check the control unit fan and airways. Check ambient temperature.
Check link between TEMPWARN signal output (X2/9) and controller.
Reset required.
Note: see Section 3.11
EEPROM
FEEDBACK
GEAR BOX
HOMING (does not go off
after spindle rotates)
KK TEMP
- Spindle Motors 1
- Overview of Sections 3
- About this documentation 5
- About this document 6
- Contents 10
- Spindle Drives 13
- INDRAMAT 15
- 1.2 Safety Guidelines 16
- 1.3 The Equipment Required 18
- Checking the drive 19
- Condition of wiring 19
- Cross sections of power 19
- Operating the drive with the 22
- Checking the speed/ 22
- 2. Operating the Controllers 27
- Operating mode switch 28
- R 5 3 1 2 1 29
- Switching into parameter 31
- Reading a parameter record 32
- Changing to another 32
- Display Definition 33
- Possible fault 35
- Possible fault messages 36
- 3. Controller Functions 37
- 3.2 Speed Command Value 38
- X2 control inputs 39
- Drehzahlsollwert 39
- Function conversion 41
- Speed limits 41
- Binary Coding 42
- Speed command value 42
- Floating-Point Coding 43
- Possible error message in 43
- Drehzahlsollwertrampen 45
- Instructions for using the 47
- Conversion formula (alterna 47
- 3.5 Command Value Smoothing 48
- Smoothing time constant 49
- 3.6 Spindle Positioning 50
- Spindelpos Standard 52
- Changing the direction of 53
- Direction of positioning 53
- 3600 spindle positions 54
- Entering position command 54
- Priority of the position 54
- Para-Spindel-3600 55
- Positioning accuracy 56
- Para-Spindel-refer 57
- Display: 59
- Torque build-up 62
- Ramp function 62
- Speed dependent 63
- Braking without overshoot 63
- P-GAIN data: 64
- of tacho filter: 64
- Follow-up time T 64
- of the speed controller: 64
- C-axis functions 65
- Conversion of functions 66
- Weighting conversion speed 66
- 3.9 Power and Torque Limits 67
- Limiting with parameter or 68
- Changeover capability of the 68
- A) Percentage torque 69
- B) Torque utilization related 70
- C) Power level related to 70
- General data on the 71
- D) Torque value 71
- Para-Analo 72
- X2 signal outputs 73
- Temperaturvorwarnun 74
- 0 = fault 76
- Umschaltung-Para 77
- Switchable function 78
- 3.15 Gear Change 79
- Gear stage dependent drive 80
- Functional sequence 81
- Possible error messages on 81
- Sequence of operations 84
- 3.16 Two-Motor Changeover 85
- Possible error messages in 86
- 3.17 Master-Slave Operation 88
- Slave drive data 89
- Formula: 90
- Para-NOT-AUS 93
- (KDA, TDA) 95
- OSCILATE 99
- N<NMIN 99
- POS ORDER 99
- 4.2 Fault Diagnostics 100
- RSKCURNT (RAC 3 only) 105
- S-CIRCUIT 105
- 5. Overview of Parameters 106
- Additions list ! 108
- Para-umschaltbar 109
- Additions list! 110
- Parameter protocol! 111
- Para-M03 113
- Parameter-Blatt 115
- X2 Control inputs 116
- Signal outputs 116
- Analogue outputs 116
- 19 and terminals 1 and 2 117
- (option) 118
- 1 = acceptance of current N 119
- 6.4 SERCOS Interface (option) 120
- X6 with KDA/TDA; X13 with RAC 121
- X6 with KDA/TDA 122
- X13 with RAC 122
- 6.7 Serial Interface (option) 123
- 6.8 Motor Feedback Connection 124
- ( 400 125
- mA ) 125
- 7. Index 126
- Anschlußplan für 82 129
- < > 137
- Type code fields: 139
- TDA 1.1 - 100 - 3 - A00 139
- Figure 121: Type codes for AS 143
- High-resolution 145
- Indramat 146
Relacionado con productos y manuales para Herramientas Eléctricas Bosch 150 AC
Herramientas Eléctricas Bosch 52314 Especificaciones
(44 paginas)
(44 paginas)
Herramientas Eléctricas Bosch 3365 - 3-1/4 Planer w/ Parallel Guide Fence Especificaciones
(120 paginas)
(120 paginas)
(98 paginas)
Herramientas Eléctricas Bosch 11335K - 35 lb. Demolition Breaker Hammer Manual de instalación
(18 paginas)
(18 paginas)
Herramientas Eléctricas Bosch GTL2 Manual de usuario
(36 paginas)
(36 paginas)
Herramientas Eléctricas Bosch DWM 40 L Manual de usuario
(104 paginas)
(104 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales