Bosch LTC 9441 Series Manual de instrucciones descargar pdf (Pagina 5)

CAUTION: DO NOT EXCEED 30 VAC INPUT ON 24 VAC

MODELS. OPERATION ABOVE 30 VAC VIOLATES LOW

VOLTAGE OPERATION (CLASS 2 SPECIFICATIONS).

NORMAL OPERATION IS 24 VAC.

CUL APPROVED 24 VAC MODELS.

CAUTION: CONNECT TO CLASS 2 POWER SUPPLY

ONLY. TOTAL CURRENT THROUGH ELECTRICAL

CONNECTOR IS 4 A MAXIMUM. PAN/TILT CURRENT IS

1 A MAXIMUM. ALLOWABLE CAMERA/HOUSING IS 3 A

MAXIMUM. USE ONLY 24 VAC CAMERAS AND HOUS-

INGS ON FEED-THRU MODELS.

3.2 Recommended Mounting Equipment

LTC 9216/00 Medium duty wall mount designed to support up

to 45.3kg (100lb).

LTC 9222/00 Heavy duty wall mount designed to support up to

90.6kg (200lb).

LTC 9214/00 Heavy duty 336mm (14 inch) column mount for

ceiling or pedestal.

LTC 9224/00 Heavy duty 610mm (24 inch) column mount for

ceiling or pedestal use.

3.3 Wall Mounting

Follow the instructions provided with mounts. Mount and mounting

surface must be able to support the weight of the pan/tilt,

camera/lens, and enclosure (if used). The camera/lens/enclosure

must be properly mounted and balanced on the pan/tilt bracket.

CAUTION: THE PAN/TILTS IN THIS MANUAL CAN

ONLY BE MOUNTED UPRIGHT OR INVERTED; NEVER

HORIZONTALLY.

3.4 Camera/Lens/Enclosure Mounting

Mount the camera/lens/enclosure to the pan/tilt bracket as follows:

1. Balance the camera/lens/enclosure and adjust the unit to align

with mounting holes. Fasten with a minimum of two (2) 1/4-20

x 1/2-inch long fasteners and lock washers.

2. Make all electrical connections. Leave sufficient loops of cable

between camera/enclosure and pan/tilt to allow for tilting and

panning.

3 INSTALLATION

THIS INSTALLATION SHOULD BE MADE BY A QUALI-

FIED SERVICE PERSON AND CONFORM TO ALL LOCAL

CODES.

ALWAYS DISCONNECT POWER TO UNIT AT CON-

TROLLER PRIOR TO CONNECTING OR DISCONNECT-

ING PAN/TILT ELECTRICAL CONNECTOR. PAN/TILT TO

BE MOUNTED AWAY FROM UNAUTHORIZED ACCESS

[3 METERS (10 FEET) HIGH MINIMUM]

THESE UNITS ARE DESIGNED FOR EITHER UPRIGHT OR

INVERTED INSTALLATIONS. TO MAINTAIN WEATHER-

PROOF INTEGRITY WHEN MOUNTING OUTDOORS IN

AN INVERTED POSITION, THE UNIT MUST BE

INSTALLED IN A WEATHERPROOF ENCLOSURE (E.G.,

WEATHERPROOF DOMED HOUSING) OR A PROTECT-

ED OUTSIDE AREA.

Pan/tilts and associated equipment should be tested prior to field

installation to verify proper wiring and operation of components.

LTC 9418 & LTC 9420

The maximum load is 10kg (22lb) or 149kg-cm (129lb-in) torque at

a distance of 63.5mm (2.5in) from the center of mass of the cam-

era/lens/housing assembly to the center of the tilt table.

LTC 9440 & LTC 9441

The maximun load is 18kg (40lb) or 297kg-cm (260lb-in) torque

with center of mass located 3.12in (79.2mm) from the center of the

titl table.

The combined weight of the enclosure/camera/lens should be cen-

tered equally, front to back, on the tilt table surface for best

pan/tilt operation.

SEE RECOMMENDED APPLICATIONS.

3.1 Model Designation

LTC 9418 Series Load Rating:

22lb Load (10Kg), 129lb-in (149kg-cm) torque

Wiring: Standard Power Required: 24W

LTC 9420 Series Load Rating:

22lb Load (10Kg), 129lb-in (149kg-cm) torque

Wiring: Feed-thru Power Required: 24W

LTC 9440 Series Load Rating:

40lb Load (18kg), 260lb-in (297kg-cm) torque

Wiring: Standard Power Required: 20W

LTC 9441 Series Load Rating:

40lb Load (18kg), 260lb-in (297kg-cm) torque

Wiring: Feed-thru Power Required: 20W

Rated Motor Voltage Voltage Range

/60 models*: 120VAC, 60Hz 108 to 132

/20 models*: 24VAC, 60Hz 21.6 to 26.4

* 40lb Models 24VAC, 60Hz 23 to 26.4

/10 models: 24VAC, 50Hz 21.6 to 26.4

/50 models: 220VAC, 50Hz 207 to 253

Pan Range: 0

to 345

on standard models, 0

to 360

Continuous Pan models. Pre-position is designated as -/x1, e.g.,

LTC 9441/61

1 2 3 4 5 6 7 8 9 10 ... 15 16

Comentarios a estos manuales

Sin comentarios

Bosch LTC 9441 Series Manual de instrucciones Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch LTC 9441 Series