Bosch 17618 Manual de usuario descargar pdf (Pagina 14)

DRILL BITS

Always inspect drill bits for excessive wear. Use

only bits that are sharp and in good condition.

TWIST BITS: Available with straight and

reduced shanks for wood and light duty metal

drilling. High speed bits cut faster and last

longer on hard materials.

CARBIDE TIPPED BITS: Used for drilling

stone, concrete, plaster, cement and other

unusually hard nonmetals. Use continuous

heavy feed pressure when employing carbide

tip bits.

DRILLING WOOD

Be certain workpiece is clamped or anchored

firmly. Always apply pressure in a straight line

with the drill bit. Maintain enough pressure to

keep the drill “biting”.

-14-

You will extend the life of your bits and do

neater work if you always put the bit in

contact with the work before pulling the

rigger. During the operation, hold the tool

firmly and exert light, steady pressure. Too

much pressure at low speed will stall the tool.

Too little pressure will keep the bit from

cutting and cause excess friction by sliding

over the surface. This can be damaging to

both tool and bit.

DRILLING WITH VARIABLE SPEED

The trigger controlled variable speed feature

will eliminate the need for center punches in

hard materials. The variable speed trigger

allows you to slowly increase RPM. By using

a slow starting speed, you are able to keep

the bit from “wandering”. You can increase

he speed as the bit “bites” into the work by

squeezing the trigger.

DRIVING WITH VARIABLE SPEED

Variable speed drills will double as a power

screwdriver by using a screwdriver bit in the

drill mode. The technique is to start slowly,

increasing the speed as the screw runs

down. Set the screw snugly by slowing to a

stop. Prior to driving screws, pilot and

clearance holes should be drilled.

Operating Tips

FASTENING WITH SCREWS

This procedure shown in (Fig. 11) will enable

you to fasten materials together with your

Cordless Drill/Screwdriver without stripping,

splitting or separating the material.

First, clamp the pieces together and drill the

first hole 2/3 the diameter of the screw. If the

material is soft, drill only 2/3 the proper

length. If it is hard, drill the entire length.

Second, unclamp the pieces and drill the

second hole the same diameter as the screw

shank in the first or top piece of wood.

Third, if flat head screw is used, countersink

the hole to make the screw flush with the

surface. Then, simply apply even pressure

when driving the screw. The screw shank

clearance hole in the first piece allows the

screw head to pull the pieces tightly together.

The adjustable screw drill accessory will do all

of these operations quickly and easily. Screw

drills are available for screw sizes No. 6, 8, 10

and 12.

2. Drill same

diameter as

screw shank.

3. Countersink

same diameter

as screw head.

1. Drill 2/3 diameter and

2/3 of screw length for

soft materials, full

length for hard

materials.

Adjustable

Screw

Drill

Screw

Apply a slight

even pressure

when driving

screws.

FASTENING

WITH SCREWS

FIG. 11

BM 2610956394 07-08 7/1/08 3:04 PM Page 14

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 51 52

Comentarios a estos manuales

Sin comentarios

Samsung SMT-2231 Guida Utente (18 pagine)

Marchio: Samsung | Categoria: LED displays | Dimensione: 4.81 MB |

Indice

TFT-LCD MONITOR

User Guide

IMPORTANT SAFETY INSTRUCTIONS

User-Installer Caution

Information to user

IC Compliance Notice

CALIFORNIA USA ONLY

Contents

Viewing the Control Panels

Rear & Left Side View

     

Remote Controller

External MONITOR

OSD Menu Configurations

Auto Adjustment

Advanced Settings

Gamma, White Balance

Sound Menu

Setup Menu

Blue Screen/Melody

Energy Saving

Setting up Your PC Software

(Based on Windows XP)

Display Modes

USER'S MANUAL

Input Menu

Specifications

Più prodotti e manuali per Display a LED Samsung

Modelli	Tipo di Documento
S23C550H	Manuale Utente Samsung S23C550H, 100 pagine
MD32B	Manuale Utente Samsung MD32B, 1 pagine
LT27B550EX/XE	Manuale Utente Samsung T27B551EW User manual, 186 pagine
S24C200BL	Manuale Utente Samsung S19C200BR, 106 pagine
T27B750EW	Manuale Samsung T27B750EW, 1 pagine
820DXN-2	Manuale Utente Samsung 820DXN-2 User manual, 124 pagine
S22D300HY	Manuale Utente Samsung S24D300HL, 116 pagine
2233BW	Manuale Utente Samsung 2233GW User manual, 64 pagine
S22D300HY	Manuale Utente Samsung S22D300HY, 120 pagine
B2030	Manuale Samsung B2030 Handleiding, 82 pagine
SyncMaster 2433BW	Manuale Utente Samsung 2433BW User manual, 60 pagine
650MP-2	Manuale Utente Samsung 650MP-2 User manual, 115 pagine
C24A650X	Manuale Utente Samsung C24A650X, 115 pagine
F2380M	Manuale Utente Samsung F2380M User manual, 45 pagine
S19A10N	Manuale Utente Samsung S19A10N, 30 pagine
S24D300H	Manuale Utente Samsung S24D300H, 116 pagine
S24C650MW	Manuale Utente Samsung S24C650BW User manual, 108 pagine
TC180	Manuale Utente Samsung TC180, 65 pagine
SM933SN	Manuale Utente Samsung 2033SW User manual, 196 pagine
S27A950D	Manuale Utente Samsung S27A950D, 87 pagine

Bosch 17618 Manual de usuario Pagina 14

Comentarios a estos manuales

Samsung SMT-2231 manuali

Samsung SMT-2231 Guida Utente (18 pagine)

Indice

Più prodotti e manuali per Display a LED Samsung

Bosch 17618 Manual de usuario Pagina 14

Comentarios a estos manuales

Relacionado con productos y manuales para Herramientas Bosch 17618

Samsung SMT-2231 manuali

Samsung SMT-2231 Guida Utente (18 pagine)

Indice

Più prodotti e manuali per Display a LED Samsung