Bosch D1255RB Manual de usuario descargar pdf (Pagina 5)

GV4 Series | Approved Applications Compliance Guide | 2.0 Optional Compatible Equipment

Bosch Security Systems, Inc. | 3/12 | F01U266055-01 5

Bell Test at Arming: UL Standard 365

requires a Bell Test at arming for bank

safe and vault applications.

2.2.4 System Configuration Requirements

The following configuration and programming

options are required for UL Bank Safe and Vault

Systems. Refer to the

D9412GV4/D7412GV4/D7212GV4 Program Entry

Guide (P/N: F01U218312) for programming

information.

Safe and Vault Protective Circuits

To test the devices that protect the safe(s) or

vault(s) without sounding the bell, specify the

devices’ points as controlled zones and

supervised for trouble conditions. Refer to Point

Index in the D9412GV4/D7412GV4/D7212GV4

Program Entry Guide (P/N: F01U218312) for more

information.

Bell Configuration

UL 365 requires the bell time to be 15 to 30 min.

The Rothenbuhler 5110 Bell provides selectable

bell time through manipulation of its jumpers.

Refer to the manufacturer’s installation

instructions for more information.

In addition to the jumper settings inside the bell,

you can activate the control panel for a bell time

of 15 min.

UL 365 requires a Bell Test at arming and must

be enabled in control panel programming.

Refer to Bell Parameters in the

D9412GV4/D7412GV4/D7212GV4 Program Entry

Guide (P/N: F01U218312) for more bell time and

test programming information.

Bell Test

To enable the bell test feature, you enable an

unused area of the control panel. Enable the bell

test feature for the unused area only. Program

Relay B as the area bell relay for the unused area.

All pass codes with authority to arm the safe or

vault and also send a Closing Report must be

valid in this area. Program the area for a five-

second exit delay. Refer to Figure 1 on page 6 for

test connections. To complete the installation for

this feature, connect the output to a D133 Relay

Module.

2.2.5 Exit Delay

The control panel’s programmed maximum exit

delay must not exceed 30 sec.

2.2.6 Equipment Requirements

 GV4 Series Control Panel

 Two (2) D126 12 V, 7 Ah batteries

 Two (2) D1218 12 V 18 Ah batteries

 D8132 Battery Charger Module

 Two (2) D8108A Enclosures

 D122 Dual Battery Harness

 D122L Dual Battery Harness

 D133 Relay Module

 EVD System (Listed Safe/Vault)

2.2.7 Wiring the Rothenbuhler 5110/4001-42

High Security Bell to the GV4 Series

Control Panel

Warning: Wear ear protection when

installing and testing the Rothenbuhler

High Security Bell.

Sound levels greater than 95 dBA at

3 m (10 ft) can occur.

1. Remove all power from the control panel.

2. Use six-conductor 1.2 mm (18 AWG) stranded

wire between the control panel and the 5110

Logic Board (located in the bell enclosure).

3. If you do not have a Silence switch,

temporarily install a 1  resistor across TB1-1

and TB1-6 on the 5110 Logic Board. The

resistor keeps the 5110’s bell silent during

the installation and alignment procedures.

Also place a temporary wire jumper across

the TB1-6 Bell Relay and TB1-7. Refer to

Figure 2 on page 7 for wiring a Silence switch.

4. Mount the D8108A’s 4001-42 External

Balanced Line Module and wire it to the 5110

Logic Board using two-conductor 0.8 mm (22

AWG) cable.

5. Wire the 4001-42 to the control panel. Refer

to Figure 2 and the Rothenbuhler installation

manual.

6. Before supplying AC and DC power to the

control panel and bell, ensure you are

wearing ear protection. The bell sounds for 2

sec and then silences during power up.

1 2 3 4 5 6 7 8 9 10 ... 29 30

Comentarios a estos manuales

Sin comentarios

Bosch D1255RB Manual de usuario Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Teclados numéricos Bosch D1255RB