Bosch GPO 14 CE Professional Instrucciones de operaciones Pagina 22
- Pagina / 133
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
English | 23
Bosch Power Tools 1 609 929 T45 | (27.11.09)
Approved Grinding Tools
All grinding tools mentioned in these operating
instructions can be used.
The permissible speed [min
-1
] or the circumfer-
ential speed [m/s] of the grinding tools used
must at least match the values given in the table.
Therefore, observe the permissible rotational/
circumferential speed on the label of the grind-
ing tool.
Dust/Chip Extraction
f Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metal can be harmful to one’s health. Touch-
ing or breathing-in the dusts can cause aller-
gic reactions and/or lead to respiratory infec-
tions of the user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in
connection with wood-treatment additives
(chromate, wood preservative). Materials
containing asbestos may only be worked by
specialists.
– Provide for good ventilation of the work-
ing place.
– It is recommended to wear a P2 filter-
class respirator.
Observe the relevant regulations in your
country for the materials to be worked.
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On and Off
To start the machine, push lock-on button 8 to-
ward the front and then press the On/Off switch
7.
To lock the pressed On/Off switch 7, push the
lock-on button 8 further toward the front.
To switch off the power tool, release the On/Off
switch 7, or when it is locked, briefly press the
On/Off switch 7 and then release it.
f Check grinding tools before using. The
grinding tool must be mounted properly
and be able to move freely. Carry out a test
run for at least one minute with no load. Do
not use damaged, out-of-centre or vibrating
grinding tools. Damaged grinding tools can
burst and cause injuries.
Speed preselection (GPO 12 E)
The required speed can be preselected with the
thumbwheel 6 (also while running).
The required speed depends on the material
and the working conditions and can be deter-
mined through practical testing.
Working Advice
f Clamp the workpiece if it does not remain
stationary due to its own weight.
f Do not strain the machine so heavily that it
comes to a standstill.
f After heavily straining the power tool, con-
tinue to run it at no-load for several minutes
to cool down the cutting/grinding tool.
For sanding applications on soft materials, e. g.,
gypsum or paint, it is recommended to use the
rubber sanding plate 17 with sanding disc 18.
Cup brushes 21 and wheel brushes are suitable
for rust removal.
max.
[mm]
[mm]
D b d [min
-1
] [m/s]
230 – – 3000 80
100 30 M 14 3000 45
D
D
b
d
OBJ_BUCH-1139-001.book Page 23 Friday, November 27, 2009 11:44 AM
- GPO Professional 1
- GPO 12 E 4
- Professional 4
- Sicherheitshinweise 5
- Funktionsbeschreibung 10
- Konformitätserklärung 11
- Schutzvorrichtungen montieren 11
- Schleifwerkzeuge montieren 12
- Zulässige Schleifwerkzeuge 12
- Staub-/Späneabsaugung 12
- Inbetriebnahme 13
- Arbeitshinweise 13
- Wartung und Service 14
- Safety Notes 15
- Safety Warnings for Polishers 16
- Functional Description 19
- Technical Data 20
- Noise/Vibration Information 20
- Declaration of Conformity 20
- Assembly 21
- Operation 22
- Maintenance and Service 23
- Disposal 24
- Avertissements de sécurité 25
- Description du fonctionnement 29
- Eléments de l’appareil 30
- Caractéristiques techniques 30
- Niveau sonore et vibrations 31
- Déclaration de conformité 31
- Montage des outils de meulage 32
- Outils de meulage autorisés 32
- Mise en marche 33
- Entretien et Service 34
- Après-Vente 34
- Elimination des déchets 35
- Instrucciones de seguridad 36
- Descripción del 40
- Utilización reglamentaria 41
- Componentes principales 41
- Datos técnicos 41
- Declaración de conformidad 42
- Útiles de amolar admisibles 43
- Operación 44
- Mantenimiento y servicio 45
- Eliminación 46
- Indicações de segurança 47
- Descrição de funções 51
- Componentes ilustrados 52
- Dados técnicos 52
- Montagem 53
- Montar ferramentas abrasivas 54
- Aspiração de pó/de aparas 54
- Funcionamento 55
- Manutenção e serviço 56
- Norme di sicurezza 57
- Descrizione del funzionamento 62
- Dati tecnici 63
- Montaggio 64
- Utensili abrasivi ammessi 65
- Messa in funzione 65
- Manutenzione ed assistenza 66
- Smaltimento 67
- Veiligheidsvoorschriften 68
- Functiebeschrijving 73
- Conformiteitsverklaring 74
- Slijpgereedschappen monteren 75
- Afzuiging van stof en spanen 75
- Ingebruikneming 76
- Tips voor de werkzaamheden 76
- Onderhoud en service 77
- Sikkerhedsinstrukser 78
- Funktionsbeskrivelse 82
- Tekniske data 83
- Støj-/vibrationsinformation 83
- Overensstemmelseserklæring 83
- Tilladt slibeværktøj 85
- Støv-/spånudsugning 85
- Ibrugtagning 85
- Arbejdsvejledning 85
- Vedligeholdelse og service 86
- Säkerhetsanvisningar 87
- Funktionsbeskrivning 91
- Buller-/vibrationsdata 92
- Försäkran om överensstämmelse 92
- Montering av skyddsutrustning 92
- Montering av slipverktyg 93
- Tillåtna slipverktyg 93
- Damm-/spånutsugning 93
- Underhåll och service 94
- Kundservice och kundkonsulter 95
- Avfallshantering 95
- Sikkerhetsinformasjon 96
- Funksjonsbeskrivelse 100
- Montering 101
- Montering av slipeverktøy 102
- Godkjente slipeverktøy 102
- Støv-/sponavsuging 102
- Service og vedlikehold 103
- Deponering 104
- Turvallisuusohjeita 105
- Toimintaselostus 109
- Tekniset tiedot 110
- Melu-/tärinätiedot 110
- Standardinmukaisuusvakuutus 110
- Suojalaitteiden asennus 111
- Hiomatyökalun asennus 111
- Sallitut hiomatyökalut 112
- Pölyn ja lastun poistoimu 112
- Käyttöönotto 112
- Työskentelyohjeita 112
- Hoito ja huolto 113
- Υποδείξεις ασφαλείας 114
- Περιγραφή λειτουργίας 119
- Τεχνικά χαρακτηριστικά 120
- Συναρμολόγηση 121
- Λειτουργία 122
- Συντήρηση και Service 123
- Service και σύμβουλος πελατών 124
- Απόσυρση 124
- Güvenlik Talimat 125
- Fonksiyon tanm 129
- Teknik veriler 130
- Gürültü/Titreşim bilgisi 130
- Uygunluk beyan 130
- Taşlama uçlarnn taklmas 131
- Müsaade edilen taşlama uçlar 132
- Toz ve talaş emme 132
- Çalştrma 132
- Bakm ve servis 133
Relacionado con productos y manuales para Herramientas Eléctricas Bosch GPO 14 CE Professional
(95 paginas)
(162 paginas)
(15 paginas)
(13 paginas)
Samsung SMT-2231 manuali
Manuali dei proprietari e guide per l'utente per Display a LED Samsung SMT-2231.
We fornisce 1 manuali pdf Samsung SMT-2231 per scaricare gratuitamente in base al tipo di documento: Guida Utente
Comentarios a estos manuales