Bosch ICP-CC404 Guía de usuario descargar pdf (Pagina 6)

ICP-CC404 | User's Guide | 4.0 Arming the System

6 Bosch Security Systems, Inc. | 12/08 | F01U089400-02

3.5 MAINS Indicator

The MAINS indicator shows if the

systems AC MAINS supply is normal or

failed.

Table 4: MAINS Indicator

Status Definition

On AC MAINS power normal.

Flashing AC MAINS supply failed.

3.6 Off Indicator/Zone Sealed

The

indicator lights when the

system is disarmed and flashes when a

zone becomes unsealed when

disarmed. The indicator stops flashing

when all zones are sealed.

3.7 On Indicator/Zone in Alarm

The

indicator lights when the

system is armed in AWAY Mode and

flashes when an alarm occurs. The

system resets this indicator after you

enter a valid user code.

3.8 FAULT Indicator

The FAULT indicator lights if the

system detects a system fault. Refer to

Section 11.0 Fault Analysis Mode on

page 11 for additional information on

system faults.

Every time a new system fault is

detected (the FAULT indicator flashes),

the codepad beeps once every min.

Pressing [#] once cancels the once a

min beep and acknowledges the fault

(the FAULT indicator lights steadily).

Table 5: FAULT Indicator

Indicator Definition

On There is a system fault you must correct.

Off The system is normal. There are no faults.

Flashing There is a system fault that must be

acknowledged.

3.9 Audible Indications

Table 6 defines the audible indicators generated by

the codepad buzzer.

Table 6: Audible Indicators

Indicator Definition

One short beep A button was pressed on the

codepad, or end of Exit Time

occurred when armed in STAY

Mode 1 or STAY Mode 2.

Two short beeps The system accepted your code.

Three short beeps The system executed the requested

function.

One long beep Indicates the end of Exit Time when

armed in AWAY Mode, or the

requested operation was denied or

aborted.

One beep every

sec

Walk Test Mode is currently active

or it is a warning before automatic

arming takes place.

One short beep

every min

There is a system fault waiting to be

acknowledged.

4.0 Arming the System

There are several ways to arm the system depending

on whether you are:

• Leaving the premises and you want all active

zones to be in a ready state for an intruder.

• Remaining in the premises and you only want

part of the system to be in a ready state for an

intruder.

If a zone is not sealed at the end of Exit Time, the

zone is automatically isolated and lights steadily on

the remote codepad. The zone becomes an active

part of the system when the zone is resealed. For

example, if a window is left open after Exit Time

expires, the window is not an active part of the

system until the window is closed. Opening the

window after Exit Time expires causes an alarm.

Table 7 defines the different methods for arming the

system.

Table 7: Arming Methods

Method Definition

AWAY Mode

Arms the entire system. Refer to

Section 4.1 Arming in AWAY Mode.

STAY Mode 1

Arms all zones except those

programmed by the installer to be

automatically isolated. Refer to Section

4.2 Arming in STAY Mode 1.

STAY Mode 2

Arms all zones except those

programmed by the Master Code

holder to be automatically isolated.

Refer to Section 4.3 Arming in STAY

Mode 2.

1 2 3 4 5 6 7 8 9 10 11 ... 23 24

Comentarios a estos manuales

Sin comentarios

Bosch ICP-CC404 Guía de usuario Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch ICP-CC404