Bosch LTC 9420 Series Instrucciones de operaciones descargar pdf (Pagina 4)

1 INSTALLATION

This installation should be made by a qualified

service person and conform to all local codes.

Always disconnect power to unit at controller

prior to connecting or disconnecting pan/tilt

electrical connector. Pan/tilt to be mounted

away from unauthorized access [3 meters (10

feet) high minimum]

The LTC 9418 Series and LTC 9420 Series

units are designed for either upright or

inverted installations. To maintain

weatherproof integrity when mounting

outdoors in an inverted position, the unit

must be installed in a weatherproof enclosure

(e.g., weatherproof domed housing) or a

protected outside area.

Pan/tilts and associated equipment should be tested prior to

field installation to verify proper wiring and operation of

components.

The maximum load is 80.5 kg-cm (70 in-lb) torque or 10 kg

(22 lb) at a distance of 63.5 mm (2.5 in) from the center of

mass of the camera/lens/housing assembly to the center of

the tilt table. The combined weight of the

enclosure/camera/lens should be centered equally, front to

back, on the tilt table surface for best pan/tilt operation. See

RECOMMENDED APPLICATIONS.

1.1 Model Designation

Model Rated Motor Voltage Pan

No.

Voltage Range Range

Standard Models

LTC 9418/60 110 VAC, 60 Hz 108 to 132 0° to 345°

LTC 9418/20 24 VAC, 60 Hz 21.6 to 26.4 0° to 345°

LTC 9418/10 24 VAC, 50 Hz 21.6 to 26.4 0° to 345°

LTC 9418/50 220 VAC, 50 Hz 207 to 253 0° to 345°

LTC 9420/60

110 VAC, 60 Hz 108 to 132 0° to 345°

LTC 9420/20

24 VAC, 60 Hz 21.6 to 26.4 0° to 345°

LTC 9420/10

24 VAC, 50 Hz 21.6 to 26.4 0° to 345°

LTC 9420/50

220 VAC, 50 Hz 207 to 253 0° to 345°

Pre-Position Models

LTC 9418/61 110 VAC, 60 Hz 108 to 132 0° to 345°

LTC 9418/21 24 VAC, 60 Hz 21.6 to 26.4 0° to 345°

LTC 9418/11 24 VAC, 50 Hz 21.6 to 26.4 0° to 345°

LTC 9418/51 220 VAC, 50 Hz 207 to 253 0° to 345°

LTC 9420/61

110 VAC, 60 Hz 108 to 132 0° to 345°

LTC 9420/21

24 VAC, 60 Hz 21.6 to 26.4 0° to 345°

LTC 9420/11

24 VAC, 50 Hz 21.6 to 26.4 0° to 345°

LTC 9420/51

220 VAC, 50 Hz 207 to 253 0° to 345°

Continuous Pan Models

LTC 9420/22

24 VAC, 60 Hz 21.6 to 26.4 0° to 360°

LTC 9420/12

24 VAC, 50 Hz 21.6 to 26.4 0° to 360°

1. The total power for all models, with both motors running, is 24 W.

Caution: Do Not Exceed 30 VAC Input on 24

VAC models. Operation above 30 VAC

violates low voltage operation (Class 2

Specifications). Normal operation is 24 VAC.

cUL Approved 24 VAC Models.

Caution: Connect to Class 2 Power Supply

only. Total current through electrical

connector is 4 A maximum. Pan/tilt current is

1 A maximum. Allowable camera/housing is 3

A maximum. Use only 24 VAC cameras and

housings on feed-thru models.

1.2 Recommended Controls

LTC 5133 Series

LTC 5134 Series

Desktop Pan/Tilt/Lens Control via

hardwired connections.

TC8561A Series Remote Receiver/Driver for a

balanced line system. For use with

LTC 8600, LTC 8800, and LTC 8900

Series systems.

1.3 Recommended Mounting Equipment

TC9216WM

Medium duty wall mount designed to

support up to 45.3 kg (100 lb).

TC9222WM

Heavy duty wall mount designed to

support up to 90.6 kg (200 lb).

TC9214CM

Heavy duty 336 mm (14 inch) column

mount for ceiling or pedestal.

TC9224CM

Heavy duty 610 mm (24 inch) column

mount for ceiling or pedestal use.

TC9218RM

Parapet/Roof mount designed to

support up to 68 kg (150 lb).

TC9300 Series

Domes

Indoor and outdoor domes designed

to contain both pan/tilt and

camera/lens combinations. Contact

your local Philips Communication and

Security Systems Inc. Sales

Representative for correct dome,

pan/tilt, camera combinations.

1.4 Wall Mounting

Follow the instructions provided with mounts. Mount and

mounting surface must be able to support the weight of the

pan/tilt, camera/lens, and enclosure (if used). The

camera/lens/enclosure must be properly mounted and

balanced on the pan/tilt bracket.

Caution: The LTC 9418 Series and LTC 9420

Series pan/tilt can only be mounted upright

or inverted; never horizontally.

1.5 Camera/Lens/Enclosure Mounting

Mount the camera/lens/enclosure to the pan/tilt bracket as

follows:

1. Balance the camera/lens/enclosure and adjust unit to

align with mounting holes. Fasten with a minimum of

two (2) 1/4-20 x 1/2-inch long fasteners and lock

washers.

2. Make all electrical connections. Leave sufficient loops of

cable between camera/enclosure and pan/tilt to allow

for tilting and panning.

1 2 3 4 5 6 7 8 9 10 11 12

Comentarios a estos manuales

Sin comentarios

Bosch LTC 9420 Series Instrucciones de operaciones Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch LTC 9420 Series