Bosch PXX875D34E Manual de instrucciones descargar pdf (Pagina 27)

Cooking assist functions en

Setting the boiling point

The point at which water starts to boil depends on the

height of your home above sea level. You can set the

boiling point if water is boiling too strongly or not

strongly enough. To do this, proceed as follows:

■ Select the basic setting ™…; see the section on

~ "Basic settings"

■ The basic setting is 3 as standard. If your home is

between 200 and 400 metres above sea level, there

is no need to set the boiling point. If not, choose the

correct setting from the following table according to

your altitude:

Note: Temperature setting 3/100 ºC is sufficient for

efficient boiling, even if the water does not boil very

strongly. However, the boiling point can be changed.

For example, you can set a lower altitude if you want the

water to boil more strongly.

Connecting the wireless temperature sensor to the

control panel

You will need to connect the wireless temperature

sensor to the control panel before using the cooking

functions for the first time.

To connect the wireless temperature sensor to the

control panel, follow the instructions below:

1. Select the ™‚… menu; see the section on ~ "Basic

settings"

The hotplate indicator will light up.

2. Select the hotplate and its indicator will light up. A

signal will sound. The å indicator will light up.

3. Press the å symbol on the wireless temperature

sensor within 30 seconds.

After a few seconds, the status of the connection

between the temperature sensor and the control

panel will appear on the hotplate's display.

■ The cooking functions are made available once the

temperature sensor has been connected to the

control panel correctly.

■ If there is a fault with the temperature sensor, the

connection may not be established correctly for the

following reasons:

– Bluetooth communication error.

– You did not press the symbol on the temperature

sensor within 30 seconds of selecting a hotplate.

– The battery in the temperature sensor has run

out.

Reset the wireless temperature sensor and follow

the connection procedure once again.

■ If the temperature sensor and the control panel are

not connected correctly due to a transmission error,

follow the connection procedure once again.

If the display continues to show incorrect connection

‚, contact our technical after-sales service.

Resetting the wireless temperature sensor

1. Touch and hold the å symbol for approximately

8-10 seconds.

While you are doing this, the temperature sensor's

LED indicator will light up three times. When the LED

lights up for the third time, it will start to reset the

temperature sensor. At this point, you will need to lift

your finger off the symbol.

Once the LED goes out, this means that the wireless

temperature sensor has been reset.

2. Repeat the connection procedure from point 2.

Setting procedure

1. Attach the temperature sensor to the saucepan; see

the section on ~ "Preparing and maintaining the

wireless temperature sensor"

2. Place a saucepan filled with sufficient liquid on the

required hotplate and always put the lid on.

3. Select the hotplate on which you have placed the

saucepan with the temperature sensor.

4. Touch the å symbol on the temperature sensor.

The indicator å will light up in the control panel.

Height

Setting ™…

0 - 100 m.

‚

100 - 200 m.

200 - 400 m.

„*

400 - 600 m.

…

600 - 800 m.

†

800 - 1000 m.

‡

1000 - 1200 m.

1200 - 1400 m.

‰

Above 1400 m.

* Basic setting

Status

‹

Connected correctly

‚

Not connected correctly: Transmission error.

Not connected correctly: Temperature sensor fault.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 51 52

Comentarios a estos manuales

Sin comentarios

Bosch PXX875D34E Manual de instrucciones Pagina 27

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Bosch PXX875D34E