Bosch D7212GV2 Guía de instalación descargar pdf (Pagina 50)

D7212GV2 | Operation and Installation Guide | 12.0 SDI Devices

50 Bosch Security Systems, Inc. | 2/07 | F01U003805-02

The DX4010i can be installed up to 305 m (1000 ft)

from the control panel, using 0.8 mm (22 AWG) wire.

The DX4010i was not investigated by UL. Do not use

DX4010i in UL Listed installations.

The D9133 can be installed up to 305 m (1000 ft) from

the control panel using 1.2 mm (18 AWG) wire. The

D9133 was not investigated by UL. Do not use the

D9133 in UL Listed installations.

12.4.2 Address Settings

No jumper settings are required for the D9133 (SDI

Address 80) for home or building automation purposes

(Figure 24). Remove the jumper shunts for this purpose.

Figure 24: D9133 Jumper Setting for Address 80

1234

The DX4010i has specific DIP switch settings for SDI

Address 80 when home or building automation is

desired. Figure 25 shows the correct settings for

Address 80.

Figure 25: DX4010i DIP Switch Settings

SER

RxTx

BUS

Rx Tx

LED

ENABLE

DB9 GND

ENABLE

1 2 4 8 16 32 64 128

123456

1 2 4 8 16 32 64 128

123456

1 - Address DIP switches

2 - OFF position

3 - ON position

4 - SDI Address 80 switch settings

12.4.3 Supervision

Supervision of the serial interface module is available

through programming. Supervision is not required to

use a DX4010i or a D9133.

If supervised, and the serial interface module does not

respond to control panel supervision polls, the control

panel sends an SDI Failure Report to the receiver. If it

fails to communicate with the DX4010i or the D9133,

SERVC SDI 80 displays at the keypad. The SDI

Failure Report includes the address of the troubled

module indicating which module needs service.

12.5 SDI Address 88

SDI Address 88 is available with the D7212GV2

Control Panel and is used for several different

applications. When using SDI Address 88, connect

only one listed device at a time.

12.5.1 D9133DC Direct Connect Programming

Module

Use the D9133DC Direct Connect Programming

Module to handle local programming of the

D9412GV2 and D7412GV2 Control Panels. In

addition, the D9133DC allows diagnostic and history

retrieval.

D9133DC is not UL Listed, and cannot

remain connected to the system for UL

applications.

Connecting the D9133DC

1. Configure D9133DC for SDI Address 88. To

program the control panel when the reset pin is in

the unlocked position, program Enable SDI RPS to

Yes in the GV2AUX handler.

2. Connect D9133DC to Com Port 1 or Com

Port 2 on the PC. The D9133DC has a DB-9

female serial connector. A null-modem cable must

be purchased separately to connect the D9133DC

to a PC.

3. Using 0.8 mm (22 AWG) or 1.2 mm (18

AWG) wire, connect the D9133DC SDI terminals

(SDI PWR, SDI A, SDI B, and SDI COM) to the

control panel’s SDI terminals (Terminals 29 to 32).

To send or receive the control panel’s program, place

the Reset Pin in the Locked or Unlocked position.

Locking the Reset Pin when programming

the control panel improves the uploading

and downloading times.

Used as an External Modem

The D9133DC can operate as an external modem

when using Remote Programming Software (RPS) with

the control panel. Refer to the D9412GV2/D7412GV2

Program Entry Guide (P/N: F01U003636) for

programming details.

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 59 60

Comentarios a estos manuales

Sin comentarios

Bosch D7212GV2 Guía de instalación Pagina 50

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch D7212GV2