Bosch AMAX panel 2000 ICP-AMAX-P Manual de instalación Pagina 30
- Pagina / 92
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
30 en | Fault and Tamper Description AMAX panel 2000 / AMAX panel 2000 EN
F.01U.241.127 | V4 | 2011.12 Installation Manual Bosch Sicherheitssysteme GmbH
Zone Indicator
5.1 Accessory Modules Fail
The zone indicator 1 lights to indicate external module fail.Enter [1] to step to external
modules fail list for more information.
5.1.1 Keypad 1 fail
Condition:
1. Keypad fail is reported at any time when communication fails between the panel and
address 1 keypad.
Restore:
Communication between panel and keypads comes back to normal and fault is reset.
Supervise:
1 Accessory Modules Fail ( Refer to 5.1 )
1 Keypad 1 fail (Refer to 5.1.1 )
2 Keypad 2 fail (Refer to 5.1.2 )
3 DX 3010 Fail (Refer to 5.1.3 )
4 B420/DX 4020 /-G Fail (Refer to 5.1.4 )
2 Power Faults (Refer to 5.2 )
1 AC Fault (Refer to 5.2.1 )
2 Fault Battery (Refer to 5.2.2 )
3 Aux Power Supply Fault (Refer to 5.2.3 )
4 Bosch Option Bus Power Fault (Refer to 5.2.4 )
5 RF Power Fault (Refer to 5.2.5 )
3 Warning Device Failure List (Refer to 5.3 )
1 Warning Device 1 Disconnected (Refer to 5.3.1 )
2 Warning Device 1 Short (Refer to 5.3.2 )
3 Warning Device 2 Disconnected (Refer to 5.3.3 )
4 Warning Device 2 Short (Refer to 5.3.4 )
4 Telephone Line Fail (Refer to 5.4 )
5 Date and Time Fail (Refer to 5.5 )
6 Communications failure (Refer to 5.6 )
1 Communication Failure 1 (Refer to 5.6.1 )
2 Communication Failure 2 (Refer to 5.6.2 )
3 Communication Failure 3 (Refer to 5.6.3 )
4 Communication Failure 4 (Refer to 5.6.4 )
7 Tamper (Refer to 5.7 )
1 On board Tamper (Refer to 5.7.1 )
2 Keypad 1 Tamper (Refer to 5.7.2 )
3 Keypad 2 Tamper (Refer to 5.7.3 )
4 Keypad Lock out (Refer to 5.7.4 )
5 Sensor Tamper (Refer to 5.7.5 ) (Zone 1-8)
6 Tamper Zone (Refer to 5.7.6 ) (Zone 1-8)
8 External Fault (Refer to 5.8 )
- ICP-AMAX-P / ICP-AMAX-P-EN 1
- 1 Graphics 3
- 4 ICP-AMAX-P / ICP-AMAX-P-EN 4
- Table of Contents 5
- 1 Short Information 10
- 2 System Overview 11
- 3 Installation 12
- ICP-AMAX-P 13
- ICP-AMAX-P-EN 13
- 3.3 Programming 14
- Table 3.2 Keypad Indicators 15
- Figure 3.3 17
- Figure 3.2 17
- Figure 3.4 18
- 4User Guide 19
- 1 2 3 … 20
- Table 4.3 Keypad sounds 21
- 4.1 Arming the System 22
- 4.1.2 Arming in STAY mode 23
- 4.2 Disarming the System 24
- 4.4 Walk test mode 25
- 4.5 Event Memory Recall mode 25
- 4.6 Reset the Control Panel 26
- 4.7 Bypassing 26
- 4.9 Change individual code 27
- 4.11 Domestic Dialing 28
- 5.1 Accessory Modules Fail 30
- 5.1.2 Keypad 2 fail 31
- 5.1.3 DX3010 Fail 31
- 5.2 Power Faults 32
- 5.3 Warning Device Failure 33
- 5.4 Telephone Line Fault 34
- 5.5 Date and Time Fail 35
- 5.6 Communication Failure 35
- 5.7 Tamper Condition 36
- 5.7.4 Keypad lock out 37
- 5.7.5 Sensor Tamper 37
- 5.7.6 Zone Tamper 37
- 5.8 External Fault 38
- 6 System Functions 39
- 6.2 Siren Test 40
- 6.4 View date and time 40
- 6.5 Walk Test Mode 40
- 6.6 Event Memory Recall Mode 41
- 6.7 Reset panel/clear siren 41
- 6.8 Initiate a Modem Call 42
- 6.9 Send Test Report 42
- 6.10 Bypass Zones 42
- 6.11 Show Zone Type 42
- 6.14 Change individual code 43
- 6.15 Setting date and time 43
- 6.16 Add/delete User Codes 44
- 6.19 Enter Programming Mode 45
- 7 System Informations 1 48
- 7.4 Software 49
- 7.5 Domestic Dialing 50
- 7.6 Reporting Formats 50
- 7.7 Dialer Information 51
- Table 7.1 Dialing Digits 52
- 7.8 Access Codes 54
- 7.8.3 User Codes 55
- 8 System Informations 2 56
- BBBBB7DPSHU6ZLWFK 57
- BBBBB=RQH6ZLWFK 57
- 8.1.4 Zone Bypass 62
- 8.1.5 Forced Arming 62
- 8.1.6 Silent Alarm 62
- 8.1.7 Zone Lockout 62
- 8.1.8 Zone Tamper 63
- 8.1.9 Zone Fault 63
- 8.1.10 Zone Report 63
- 8.1.11 Zone Chime Mode 63
- 8.2.3 Auto Test Report 68
- 8.4 Output Process 69
- 8.5 System Event Time 72
- 8.6 Optional Equipment 73
- 9 Technical Data 75
- 9.2 Interface Description 77
- 10 Programming sheets 78
- 10.1.2 Domestic Programming 79
- 10.2.1 Report Options 79
- 10.4 Zone Programming 82
- 10.5 Output Programming 85
- 10.6.1 Installer code 87
- 10.6.2 User Codes 87
- 11 Troubleshooting 89
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 2000 ICP-AMAX-P
Los Sistemas De Control De Acceso De Seguridad Bosch CC880/LP880, SC8016 Especificaciones
(44 paginas)
(44 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 2000 ICP-AMAX-P Manual de instrucciones
(32 paginas)
(32 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.148 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales