Bosch AMAX panel 2000 ICP-AMAX-P Manual de instalación Pagina 37
- Pagina / 92
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AMAX panel 2000 / AMAX panel 2000 EN Fault and Tamper Description | en 37
Bosch Sicherheitssysteme GmbH Installation Manual F.01U.241.127 | V4 | 2011.12
The Tamper condition is reset when the Keypad is closed and Tamper condition is reset.
Supervise:
1. Report the Tamper condition to configured destination on Location 140 when the
Tamper Condition is detected.
2. Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators).
3. When the Tamper Condition is reset, send the restored report to the configured
destinations. The FAULT indicator is turned off when there is no other system fault.
5.7.4 Keypad lock out
Condition:
Invalid code is entered more times than allowed by the code retry attempts (programmed in
location 179)
Restore:
Keypad lock out is reset when the Keypad lockout time (3min) is expired and the fault is reset.
Supervise:
1. Report the Keypad lock out to configured destination on Location 140 when the Keypad
lock out is detected.
2. Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators).
3. When the Keypad lock out Condition is reset, send the restored report to the configured
destinations.The FAULT indicator is turned off when there is no other system fault.
5.7.5 Sensor Tamper
Condition:
Tamper contact is triggered (Zone is programmed as Dual End of Line)
Restore:
Tamper contact is restored and Tamper condition is reset.
Supervise:
1. Report the Sensor Tamper to configured destination on Location 140 when the Sensor
Tamper is detected.
2. Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators).
3. When the Tamper condition is reset, send the restored report to the configured
destinations. The FAULT indicator is turned off when there is no other system fault.
Sensor Tamper Zone Indication
The zone indicator 5 lights to indicate Sensor Tamper conditions.
Enter [5] to step to Zone Indicator list to identify the Zone where the Sensor Tamper comes
from.
1=Zone 1 2=Zone 2 3=Zone 3 4=Zone 4 5=Zone 5 6=Zone 6 7=Zone 7 8=Zone 8
5.7.6 Zone Tamper
Condition:
Tamper contact (direct connected to the Zone) is triggered (Zone type = Tamper)
Restore:
Tamper contact is restored and Tamper condition is reset.
Supervise:
1. Report the Tamper condition to configured destination on Location 140 when the
Tamper condition is detected.
2. Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators).
3. When the Tamper condition is reset, send the restored report to the configured
destinations. The FAULT indicator is turned off when there is no other system fault.
- ICP-AMAX-P / ICP-AMAX-P-EN 1
- 1 Graphics 3
- 4 ICP-AMAX-P / ICP-AMAX-P-EN 4
- Table of Contents 5
- 1 Short Information 10
- 2 System Overview 11
- 3 Installation 12
- ICP-AMAX-P 13
- ICP-AMAX-P-EN 13
- 3.3 Programming 14
- Table 3.2 Keypad Indicators 15
- Figure 3.3 17
- Figure 3.2 17
- Figure 3.4 18
- 4User Guide 19
- 1 2 3 … 20
- Table 4.3 Keypad sounds 21
- 4.1 Arming the System 22
- 4.1.2 Arming in STAY mode 23
- 4.2 Disarming the System 24
- 4.4 Walk test mode 25
- 4.5 Event Memory Recall mode 25
- 4.6 Reset the Control Panel 26
- 4.7 Bypassing 26
- 4.9 Change individual code 27
- 4.11 Domestic Dialing 28
- 5.1 Accessory Modules Fail 30
- 5.1.2 Keypad 2 fail 31
- 5.1.3 DX3010 Fail 31
- 5.2 Power Faults 32
- 5.3 Warning Device Failure 33
- 5.4 Telephone Line Fault 34
- 5.5 Date and Time Fail 35
- 5.6 Communication Failure 35
- 5.7 Tamper Condition 36
- 5.7.4 Keypad lock out 37
- 5.7.5 Sensor Tamper 37
- 5.7.6 Zone Tamper 37
- 5.8 External Fault 38
- 6 System Functions 39
- 6.2 Siren Test 40
- 6.4 View date and time 40
- 6.5 Walk Test Mode 40
- 6.6 Event Memory Recall Mode 41
- 6.7 Reset panel/clear siren 41
- 6.8 Initiate a Modem Call 42
- 6.9 Send Test Report 42
- 6.10 Bypass Zones 42
- 6.11 Show Zone Type 42
- 6.14 Change individual code 43
- 6.15 Setting date and time 43
- 6.16 Add/delete User Codes 44
- 6.19 Enter Programming Mode 45
- 7 System Informations 1 48
- 7.4 Software 49
- 7.5 Domestic Dialing 50
- 7.6 Reporting Formats 50
- 7.7 Dialer Information 51
- Table 7.1 Dialing Digits 52
- 7.8 Access Codes 54
- 7.8.3 User Codes 55
- 8 System Informations 2 56
- BBBBB7DPSHU6ZLWFK 57
- BBBBB=RQH6ZLWFK 57
- 8.1.4 Zone Bypass 62
- 8.1.5 Forced Arming 62
- 8.1.6 Silent Alarm 62
- 8.1.7 Zone Lockout 62
- 8.1.8 Zone Tamper 63
- 8.1.9 Zone Fault 63
- 8.1.10 Zone Report 63
- 8.1.11 Zone Chime Mode 63
- 8.2.3 Auto Test Report 68
- 8.4 Output Process 69
- 8.5 System Event Time 72
- 8.6 Optional Equipment 73
- 9 Technical Data 75
- 9.2 Interface Description 77
- 10 Programming sheets 78
- 10.1.2 Domestic Programming 79
- 10.2.1 Report Options 79
- 10.4 Zone Programming 82
- 10.5 Output Programming 85
- 10.6.1 Installer code 87
- 10.6.2 User Codes 87
- 11 Troubleshooting 89
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 2000 ICP-AMAX-P
Los Sistemas De Control De Acceso De Seguridad Bosch CC880/LP880, SC8016 Especificaciones
(44 paginas)
(44 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 2000 ICP-AMAX-P Manual de instrucciones
(32 paginas)
(32 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.366 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales