Bosch AMAX panel 2000 ICP-AMAX-P Manual de instalación Pagina 39
- Pagina / 92
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AMAX panel 2000 / AMAX panel 2000 EN System Functions | en 39
Bosch Sicherheitssysteme GmbH Installation Manual F.01U.241.127 | V4 | 2011.12
6 System Functions
6.1 Duress alarm
This function allows code holders to perform a keypad Duress Alarm.
A Keypad Duress Alarm is used as a silent holdup alarm when 0 is added to the end of a valid
Code used to disarm the system.
User
Code
Install
er
Code
Function Description
• • 0 # Duress alarm (Refer to 6.1 )
• • 1 # Siren test (Refer to 6.2 )
• • 2 # Fault and Tamper analysis (Refer to 6.3 )
• • 3 # View date and time (Refer to 6.4 )
• • 4 # Walk test (Refer to 6.5 )
• • 5 # Event memory recall (Refer to 6.6 )
• • 6 # Reset panel/clear siren (Refer to 6.7 )
• • 7 # Initiate a modem call (Refer to 6.8 )
• • 8 # Send Test report (Refer to 6.9 )
• • 9 # Bypass (inhibit) (Refer to 6.10 )
• • 96 # Show Zone type (Refer to 6.11 )
• 97 # Bypass all faults (Refer to 6.12 )
•98#
*
Enable=# / Disable=* installer code user's access (Refer to
6.13 )
• • 99 # Change individual code (Refer to 6.14 )
• 955 # Change/View date and time (Refer to 6.15 )
• 956 # Add/delete a level 2 user (Refer to 6.16 )
• 956 # Add/delete Remote Radio User Codes (Refer to 6.17 )
• 957 # Change domestic phone numbers (Refer to 6.18 )
• 958 # Enter Programming Mode (Refer to 6.19 )
• 959 # Exits from installer’s programming mode without saving
the programmed data. (Refer to 6.20 )
• 960 # Exits from installer’s programming mode with saving the
programmed data. (Refer to 6.21 )
• 961 # Resets the control panel to factory defaults. (Refer to
6.22 )
• 962 # Copies the control panel memory to the programming key.
(Refer to 6.23 )
• 963 # Copies the programming key data to the control panel
memory. (Refer to 6.24 )
• 999 # Displays the software version number or control panel
type. (Refer to 6.25 )
Default Pads on PCB Default the control panel with the hardware (Refer to
6.26 )
- ICP-AMAX-P / ICP-AMAX-P-EN 1
- 1 Graphics 3
- 4 ICP-AMAX-P / ICP-AMAX-P-EN 4
- Table of Contents 5
- 1 Short Information 10
- 2 System Overview 11
- 3 Installation 12
- ICP-AMAX-P 13
- ICP-AMAX-P-EN 13
- 3.3 Programming 14
- Table 3.2 Keypad Indicators 15
- Figure 3.3 17
- Figure 3.2 17
- Figure 3.4 18
- 4User Guide 19
- 1 2 3 … 20
- Table 4.3 Keypad sounds 21
- 4.1 Arming the System 22
- 4.1.2 Arming in STAY mode 23
- 4.2 Disarming the System 24
- 4.4 Walk test mode 25
- 4.5 Event Memory Recall mode 25
- 4.6 Reset the Control Panel 26
- 4.7 Bypassing 26
- 4.9 Change individual code 27
- 4.11 Domestic Dialing 28
- 5.1 Accessory Modules Fail 30
- 5.1.2 Keypad 2 fail 31
- 5.1.3 DX3010 Fail 31
- 5.2 Power Faults 32
- 5.3 Warning Device Failure 33
- 5.4 Telephone Line Fault 34
- 5.5 Date and Time Fail 35
- 5.6 Communication Failure 35
- 5.7 Tamper Condition 36
- 5.7.4 Keypad lock out 37
- 5.7.5 Sensor Tamper 37
- 5.7.6 Zone Tamper 37
- 5.8 External Fault 38
- 6 System Functions 39
- 6.2 Siren Test 40
- 6.4 View date and time 40
- 6.5 Walk Test Mode 40
- 6.6 Event Memory Recall Mode 41
- 6.7 Reset panel/clear siren 41
- 6.8 Initiate a Modem Call 42
- 6.9 Send Test Report 42
- 6.10 Bypass Zones 42
- 6.11 Show Zone Type 42
- 6.14 Change individual code 43
- 6.15 Setting date and time 43
- 6.16 Add/delete User Codes 44
- 6.19 Enter Programming Mode 45
- 7 System Informations 1 48
- 7.4 Software 49
- 7.5 Domestic Dialing 50
- 7.6 Reporting Formats 50
- 7.7 Dialer Information 51
- Table 7.1 Dialing Digits 52
- 7.8 Access Codes 54
- 7.8.3 User Codes 55
- 8 System Informations 2 56
- BBBBB7DPSHU6ZLWFK 57
- BBBBB=RQH6ZLWFK 57
- 8.1.4 Zone Bypass 62
- 8.1.5 Forced Arming 62
- 8.1.6 Silent Alarm 62
- 8.1.7 Zone Lockout 62
- 8.1.8 Zone Tamper 63
- 8.1.9 Zone Fault 63
- 8.1.10 Zone Report 63
- 8.1.11 Zone Chime Mode 63
- 8.2.3 Auto Test Report 68
- 8.4 Output Process 69
- 8.5 System Event Time 72
- 8.6 Optional Equipment 73
- 9 Technical Data 75
- 9.2 Interface Description 77
- 10 Programming sheets 78
- 10.1.2 Domestic Programming 79
- 10.2.1 Report Options 79
- 10.4 Zone Programming 82
- 10.5 Output Programming 85
- 10.6.1 Installer code 87
- 10.6.2 User Codes 87
- 11 Troubleshooting 89
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 2000 ICP-AMAX-P
Los Sistemas De Control De Acceso De Seguridad Bosch CC880/LP880, SC8016 Especificaciones
(44 paginas)
(44 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 2000 ICP-AMAX-P Manual de instrucciones
(32 paginas)
(32 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.653 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales