Bosch K2200 Series Guía de usuario descargar pdf (Pagina 45)

K2200 Series | User Guide | 6.0 Installer Commands EN | 45

Bosch Security Systems | 7/03 | 17376 v1.1 / 47491C

6.1.7 Using the D Command

Each of the settings in the D command is fully

described above.

1. Present an editor key to the faceplate reader.

2. Enter the password and press [ENT], if required.

3. You will now see the CMD prompt.

4. Type [D] and press [ENT].

CMD D_

5. Use the up and down arrow keys to select the

door.

Enter a value, in seconds, between 0 and 255 for

the amount of time the lock will operate. Press

[ENT].

DR 1 LRT 5

Press [NXT] to go to the next field.

6. A value greater than zero enables door

monitoring. The value entered is the time in

seconds that, when added to the lock release

time, a door left open warning will be generated.

Press [ENT]

DR 1 TP 0

Press [NXT] to go to the next field.

7. Lock Mode Options - This is an option field. To

change a setting press the number corresponding

to the option you want to change. If an option is

set, its number will be displayed, if not set, a -

(dash) will be displayed.

Table 19: Lock Mode Options

Option Description

Unset

Fail-secure lock

Set

Fail-safe lock

Unset

Normal RTE, door contact

Set

Emergency override, free exit

Unset

Normal RTE report

Set

Request for entry report

Unset

No AVR module

Set

AVR module attached

Unset

No alarm module

Set

Alarm module attached

Unset

Normal operation

Set

Exit out of hours allowed

Unset

No PIN reader with time profiles

Set

PIN reader with time profiles

attached

Not Used, leave Unset

Press [ENT] when all required options are set.

Press [NXT] to go to the next field.

8. Door 1, Lock Mode 2 (Options) - This display

consists of 8 more option settings represented

either by a number or a - (dash). Each setting is

changed by pressing a number between 1 and 8.

When set, the number will appear: when not set,

a - (dash) will replace the number. At startup, all

settings will be off.

DR 1 M2--------

Table 20: Lock Mode 2 Options

Options Description

Set:

RTE with no lock output. This is

designed for use on the secure

side of a door where exit is via a

mechanical handle, etc. Pressing

the Request to Exit switch shunts

the door contact but does not

activate the lock.

Unset:

RTE with lock output. This is the

default setting. When the Request

to Exit switch is pressed, the lock

state is changed and the door can

be opened.

Set:

Early lock release time. When set,

the lock is de-activated a maximum

of two seconds after the door is

opened.

Unset:

lock release time operates normally

Lock is de-activated when the lock release

time expires or the door closes.

Set:

Log authorized event only when

door opened. When set,

authorized events are only reported

if the door is opened.

Unset:

All events are logged whether or

not the door is opened

Elevator

Control:

This option is not user

configurable and is set using

Readykey for Windows

5 – 8

These settings are not currently used.

Press [NXT] to go to the next field. (Remember

to press [ENT] to save changes).

9. PIN Reader Time Profile - Only used when a

Readykey PIN reader with time profiles is

attached. When the time profile is active, only a

valid key is required; when inactive, a valid key

plus PIN is required for access. A time profile of

0 requires a valid key plus PIN at all times. Press

[ENT].

DR 1 PINTP 0

Press [ESC] to return to the CMD prompt.

1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 61 62

Comentarios a estos manuales

Sin comentarios

Bosch K2200 Series Guía de usuario Pagina 45

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch K2200 Series