Bosch SE2005 Guia de preparacion descargar pdf (Pagina 19)

Security Escort | Installation and Setup Guide | 2.0

ment Estimation

EN | 19

Bosch Security Systems | 1/09 | 33831E

Using a Standard Transponder,

Receivers, and Laptop Computer to

Determine Receiver Location

Note:

System software and an area map

must be installed on a laptop

computer to use this method.

A standard transponder with long

multiplex wires connected to standard

receivers can be used to see actual

alarm location before the receivers

are placed. Place the receivers in the

proposed locations wired back to the

transponder. Program the receivers

with their locations in the

transponder database. Using the

maintenance transmitter and the

maintenance alarm database, activate

alarm transmissions within the area

surrounded by the temporarily placed

receivers. Verify that the location

accuracy is acceptable at all points

of concern. If not acceptable move the

receivers, update the receiver

location in the transponder database,

and retest. Do not test outside of the

last receiver in any direction, as

this gives incorrect locations. Repeat

this test in all areas of different

construction and concern at the site.

2.3.2 Indoor Receiver Installation

• Indoor receivers must be mounted in

a evenly spaced grid no more than

25 m (80 ft.) apart.

• Indoor receivers must be mounted

1.5 m to 1.8 m (5 ft. to 6 ft.)

above the floor. This is true even

if this is a single story building.

Do not mount receivers above the

ceiling or in roof rafters.

• In multistory buildings, the

receivers must be mounted directly

above the receivers on the floor

below. The same number of receivers

must be used on each floor level.

If you meet all of the indoor

installation guidelines, you can

expect the computed location to

indicate the correct floor about

95% of the time.

• Receivers must not be mounted

within 30 cm (1 ft.) of any metal

object, including wire mesh, metal

foil, metal pipe, and HVAC ducting

in walls.

• Take care that large metal objects

do not shield a receiver from a

protected area. For example; metal

staircases, metal food serving

lines, metal walls, lead lined

walls, metal roofs, wire mesh in

walls, walk-in freezers, and

refrigerators.

For the best indoor and outdoor

location or an indoor only system.

• Mount the indoor receivers on the

recommended 25 m (80 ft.) grid,

with the last row of indoor

receivers on the outside wall of

the building. Do this even if the

building is less than 25 m (80 ft.)

wide or long.

• There should be a receiver at each

outside corner of a building.

Handling two protected buildings

sharing a common wall with floor

levels that do not match

• Ask the customer which building has

areas of greater concern and favor

the recommended mounting heights in

that building.

• The recommended 25 m (80 ft.)

maximum indoor spacing grid should

be maintained throughout both

buildings as if the wall in

question was not there. Mounting

heights only for those receivers at

or near (within 6 m [20 ft.]) the

wall in question should be

affected. Mounting heights for all

other receivers in the buildings

must follow the indoor

recommendation. Mark the

recommended mounting height for

receivers on the higher floor level

and also mark the recommended

mounting height for receivers on

the lower floor level. Mount the

receiver at its normal grid

location midway between these two

heights, but not above the ceiling

level of the lower floor.

2.3.3 Outdoor Receiver Installation

• Outdoor receivers must be mounted

in an evenly spaced grid no more

than 90 m (300 ft.) apart.

• Outdoor receivers must be mounted 3

m (10 ft.) above the ground.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 53 54

Comentarios a estos manuales

Sin comentarios

Bosch SE2005 Guia de preparacion Pagina 19

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch SE2005