Bosch LTC 8555 Manual de instrucciones descargar pdf (Pagina 27)

Bosch Security Systems | December 8, 2004

LTC 8100, LTC 8200, LTC 8300 Series | Instruction Manual | Video Monitor Display

8.2.6 Location 7 - Remote Lock Indication

This location will display characters

to indicate that

control over the movements of the camera being viewed

have been locked by a user. Control over this camera is

now possible only by the user who locked the camera, or

has higher priority. If the camera is not locked, the icon is

not displayed. If a user error has occurred, this location

will temporarily hold part of the error number.

8.2.7 Location 8 - Monitor Lock Indication

This location will display characters

to indicate that

the monitor has been locked by a user. The camera

currently being viewed cannot be changed except by the

user who locked the monitor, or has higher priority. If the

monitor is not locked, the icon will not be displayed. If a

user error has occurred, this location will temporarily

hold part of the error number.

8.2.8 Location 9 - Sequence Type Indication

This location displays the type of sequence currently

loaded on the monitor. An absolute sequence is

indicated by the characters

meaning that monitors

programmed in the sequence program refer to the exact

monitor(s) where the sequence may be run. Sequences

created via the system keyboards are always of this type,

so absolute sequences are the only type possible in a base

system. Relative sequences are designated by the

characters

in this location. These sequences will run

on any monitor or group of monitors, and can only be

programmed via the optional LTC 8059/00 MCS for

Windows or the LTC 8850/00 GUI software on a PC.

8.2.9 Locations 10 and 11 - Sequence Number

The sequence number currently active for the monitor is

displayed here. This is a number between 1 and 60, or 00

to indicate that no sequence is loaded.

8.2.10 Location 12 - Sequence Status Indication

This location indicates the status of the sequence active in

the monitor. Possible character combinations are:

1. ^

: the current sequence is sequencing in a

forward direction.

: the current sequence is sequencing in a

reverse direction.

3. ^

: the sequence is stopped, but if started again

would sequence in a forward direction.

: the sequence is stopped, but if started again

would sequence in a reverse direction.

8.3 Monitor Message

The monitor message is a stationary 12-character title

which may be placed on a monitor instead of the

System Status display. Specific monitor messages can

be programmed from either the keyboard

(see User Function 17 in Section 13) or the optional

LTC 8059 MCS package or the LTC 8850/00 GUI

software.

8.4 Broadcast Message

A message can be sent by the operator of the PC using

the optional LTC 8059 MCS package or the

LTC 8850/00 GUI software to all the monitors in the

system. This message may be up to 24 characters, and

can be used to notify all users at all monitor locations of

important information. The message, along with its

beginning and ending time and date, is also printed on

the logging printer (if one is connected), as well as any

user acknowledgment. The broadcast duration may be set

for 1 to 60 seconds. The message is displayed on a line

by itself.

8.5 Program Prompts

During entry of sequence programming via the keyboard,

the Allegiant system prompts the user on the monitor his

keyboard is currently controlling. The display will return

to its previous form when the user leaves the

programming mode.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 63 64

Comentarios a estos manuales

Sin comentarios

Bosch LTC 8555 Manual de instrucciones Pagina 27

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8555