Bosch LTC 8555 Manual de instrucciones descargar pdf (Pagina 44)

Bosch Security Systems | December 8, 2004

LTC 8100, LTC 8200, LTC 8300 Series | Instruction Manual | Keyboard User Functions

13.1.13 User Function 12 -

Default All Monitor Overlays

User Function 12 can be used by users with the

priority level 1, to reset all monitor overlays to default

characteristics; bottom center of screen, and full

brightness. After entering the mode, press [Enter]to

reset all monitor overlays. If using the LTC 8555 Series

keyboard, press [User] to exit.

13.1.14 User Function 13 -

Print System Configuration Tables

Users with priority level 1 can use this function to print

the contents of the various tables programmed. Move

the joystick up and down to select a table, then press

[Enter] to send it to the printer port. If using the

LTC 8555 Series keyboard, press [User] to exit.

13.1.15 User Function 14 -

Reserved Function

13.1.16 User Function 15 -

System Reset

The system may be reset from the keyboard by users

with priority level 1. After entering this mode, the

video monitor screen indicates RESET SYSTEM.

Enter the password via the numeric keypad, and

press [Enter]. The system will then reset. If using the

LTC 8555 Series keyboard, press [User] to exit the

mode without resetting the system.

NOTE: The system should be reset whenever a change

is made on the main CPU module’s DIP switches.

Alternatively, the main power to the CPU bay may be

switched off for 10 seconds, then restored. Depending

on the size and complexity of the system, several

seconds may be required before operation is restored.

This time is due to the amount of initialization tasks

being performed, and is considered normal.

13.1.17 User Function 16 - Time Event

Enable/Disable

Users with priority level 1 can use this function to

enable or disable any of the programmed time event

functions. Up to 64 time event functions can be

programmed with the optional LTC 8059/00 MCS for

Windows, or the LTC 8850/00 GUI software. Moving

the joystick up and down steps through a table of the

64 time events. If an event has been programmed,

moving the joystick to the right enables the event, and

to the left disables it. The current status of an enabled

time event is displayed by this user function.

13.1.18 User Function 17 -

Set Monitor ID

User Function 17 can be used by users with the

priority level 1, to enter a (12-character) monitor

identification message for display in the top line of the

monitor overlay display on any system monitor(s).

This monitor title will be visible on the display

regardless of the camera currently being viewed. This

message can be used to identify the particular monitor

or a group of cameras assigned to this monitor. Refer

to Section 15, CHARACTER ROM TABLES, for the

available characters. After entering the mode, the

joystick is moved right or left to select the character to

be changed. The selected character is identified by a

box with a question mark inside it. The first line of the

video monitor display indicates the code number of the

character selected. Move the joystick up or down to

step through the Character ROM Table, or enter the

character’s number identified in the Tables via the

numeric keypad, then press [Enter]. Once the monitor

title has been set, press [Enter] to store it to memory.

If using the LTC 8555 Series keyboard, press [User]

to exit the mode. The user may select between this

monitor message and the status display by using

the User 5 Function described above.

13.1.19 User Function 18 -

Print Sequence

Use this function to print the contents of a

programmed sequence. Users with priority level 1 can

use the joystick to select the desired sequence, then

press [Enter] to print it to the printer port. Only those

sequences currently existing in memory will be shown

in the list. If using the LTC 8555 Series keyboard, press

[User] to exit.

13.1.20 User Function 19 -

Select Alarm Response

Users with the priority level 1 can use this function to

reset the system alarm configuration tables to one of

these predefined alarm response modes: BASIC,

AUTOBUILD, or SEQUENCE & DISPLAY. Move

the joystick up or down to select the desired mode,

then enter your user password on the numeric keypad,

and press [Enter] to update the alarm system. If using

the LTC 8555 Series keyboard, press [User] to exit.

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 63 64

Comentarios a estos manuales

Sin comentarios

Bosch LTC 8555 Manual de instrucciones Pagina 44

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8555