Bosch LTC 8555 Manual de instrucciones descargar pdf (Pagina 37)

Bosch Security Systems | December 8, 2004

LTC 8100, LTC 8200, LTC 8300 Series | Instruction Manual | Keyboard Operation

12.5.2 Arm/Disarm All Alarms

Press Alarm Control, located on the main Allegiant

menu screen to enter the menu screen containing these

options.

When using the IntuiKey:

•To arm all alarms on the monitor currently

controlled, press Arm All Alarms.

•To disarm all alarms, press Disarm All Alarms.

When using LTC 8555 Series keyboards:

•To arm all alarms, press User, Alarm, and then

[ON].

•To disarm all alarms, press [OFF].

12.5.3 Arm/Disarm Monitor

When using IntuiKey keyboards:

•Press Alarm Control, located on the main

Allegiant menu screen to enter the screen with

these options.

•To arm the monitor currently controlled, press

Arm Monitor.

•To disarm the monitor, press Disarm Monitor.

When using the LTC 8555 Series:

•To arm the monitor, press User, Monitor, then

[ON] to arm all alarms.

•To disarm all alarms, press [OFF].

NOTE: Alarm video will appear on a monitor only if the

monitor is armed and the alarm is armed for that

monitor. The monitor status display (if enabled) will show

(monitor armed).

12.5.4 Alarms Acknowledgement

Bell [Ack] is provided so system operators can respond

to alarms from the keyboard. Pressing Bell [Ack] while

the keyboard is beeping (due to an alarm condition)

always silences the beeper. Depending on alarm

configuration programming, subsequent pressing of Bell

[Ack] either clears alarm video from the monitors or has

no effect.

12.6 Sequence Control

12.6.1 Load/Clear a Sequence

To load a previously programmed sequence to run on

your monitor, press Load Sequence [Seq], enter the

desired sequence number (1 to 60), then press [Enter].

Note that loading a sequence does not automatically start

the sequence running.

Since sequences may be programmed to use more than

one monitor, all required monitors must be available. If a

sequence is already on a monitor, the operator who

loaded it originally (or an operator with a higher priority)

is permitted to load a new sequence on the monitor(s).

Others will receive an error message.

To clear a monitor sequence, press Load sequence

[Seq], then press [Enter]. Only the operator who

originally loaded it (or an operator with a higher priority)

is permitted to clear a monitor sequence. Others will

receive an error message.

If enabled, the status display area of the monitor indicates

the sequence number in the appropriate location. If no

sequence is currently loaded, 00 is displayed.

12.6.2 Run a Sequence

To run a sequence currently loaded on a monitor, press

Start Sequence [Run]. If the sequence was stopped, the

command starts sequencing. Direction of the sequencing

is indicated in the monitor status display (if enabled), by a

directional arrow and the letter R to the right of the

sequence number. If Start Sequence [Run] is pressed

while a sequence is already running, the switcher goes

immediately to the next step in the sequence. Holding

down Start Sequence [Run] produces a quick-scan

effect. If Start Sequence [Run] is depressed when no

sequence is loaded, an error results. If the monitor is in

alarm, Start Sequence [Run] controls switching of alarm

video rather than a loaded sequence.

12.6.3 Stop a Running Sequence

To stop a sequence that is currently running, press Hold

Sequence [Hold]. The monitor status display now shows

a S to the right of the sequence number. If the sequence

is already stopped, pressing Hold Sequence [Hold] has

no effect. If no sequence is currently loaded, pressing

Hold Sequence [Hold] results in an error condition. If

the monitor is in alarm, Hold Sequence [Hold] stops the

alarm switcher rather than a loaded sequence.

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 63 64

Comentarios a estos manuales

Sin comentarios

Bosch LTC 8555 Manual de instrucciones Pagina 37

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8555