Bosch LTC 8555 Manual de instrucciones descargar pdf (Pagina 39)

Bosch Security Systems | December 8, 2004

LTC 8100, LTC 8200, LTC 8300 Series | Instruction Manual | Keyboard Operation

Using the joystick, move RIGHT one step. The prompts

will shift over to the monitor number shown in the

example as M001. The monitor that was being controlled

by the keyboard before entering the programming

mode is defaulted to this position. If correct, no action is

necessary. If not, enter the desired monitor number via

the keypad, and press [Enter].

Move RIGHT again. The prompts now shift over to the

dwell time shown in the example as D02. The default

dwell time for a new sequence is always 2 seconds. If a

different dwell period is desired, change the value to any

number between 1 and 60. One line is now complete.

Press Next Step [Next] to add a second line. The camera

number automatically increments, while the monitor

number and dwell remain the same as the first line. Since

this line is correct, no change is necessary and Next Step

[Next] may be pressed 3 more times until line 5 is

reached. The joystick can be used to move around within

the spreadsheet, but only the Next Step [Next] key can

add new lines.

Continue entering camera, monitor, and dwell times in

this fashion, until finished.

If you only want to store the sequence for future use and

then exit the programming mode, press Exit / Save

[Prog]. Press Exit / Run [Run], to exit the

programming mode, store the sequence into memory,

and start the sequence running. The switcher steps

through the 5 steps in the order shown, and repeats the

sequence when it reaches the last step. To program a

sequence to run once through all its steps and then stop,

enter the value 62 for the dwell time in the last step and

press [Enter]. The dwell display will change to STP,

meaning stop. To program a sequence to run once

through all its steps and then unload itself, enter the value

63 for the dwell time in the last step, and press [Enter].

The dwell display will change to ULD, meaning unload.

To edit an existing sequence, press Program Sequence

[Prog], enter the existing sequence number, then press

[Enter]. You can insert a line into a sequence by

navigating down to the line where inserting a new line,

and press Insert Step [ON]. A new line identical to the

one you are on is added to the next step. To delete a step,

navigate to the line to be deleted, and press Delete

Current Step [OFF]. To delete all steps below the line

you are viewing, press Delete From Here To End

[Lock]. (Be careful with this feature!)

It is also possible to erase a sequence:

Press Delete From Here To End [Lock] while on the

first line of the sequence. Then press Delete Current

Step [OFF]. The sequence will be erased, and the

programming mode is automatically exited.

12.7.2 Programming a SalvoSwitching

Camera Sequence

A SalvoSwitching sequence can be used to switch a group

of monitors simultaneously as a synchronized group. To

program a Salvo sequence, enter the programming

mode as described above for a simple camera sequence.

By definition, Salvo sequencing involve more than one

monitor. An example of a simple Salvo sequence that

switches cameras on three monitors simutaneously is

shown below:

CAMERA MONITOR DWELL

11SLV

22SLV

332

71SLV

82SLV

932

21 1 S LV

22 3 SLV

23 3 2

In general, follow the instructions used for the simple

camera sequence (described above), but instead of

entering a number of seconds for steps that must switch

instantly, enter 61 and press [Enter]. This causes the

switcher to automatically change to the salvo abbreviation

SLV. Dwell time (in seconds) is entered only when you

reach the step containing the last monitor that will be

switched within the synchronized group.

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 63 64

Comentarios a estos manuales

Sin comentarios

Bosch LTC 8555 Manual de instrucciones Pagina 39

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8555