Bosch AMAX panel 4000 EN Guía de instalación Pagina 72
- Pagina / 176
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3. When the fault is reset, send the restored report to the configured destinations. The FAULT
indicator is turned off when there is no other system fault.
– RF Config Failure
Configuration Conflict Sensors
Condition:
Any one wireless zone configuration is error.
Restore:
All wireless zone configuration are correct and fault is reset.
Supervise:
1. Slow flash FAULT indicator (refer to the detailed description in chapter keypad indicators)
2. When the fault is reset, the FAULT indicator is turned off when there is no other system
fault.
Configuration Conflict Repeaters
Condition:
Any one repeater configuration is error.
Restore:
All repeater configuration are correct and fault is reset.
Supervise:
1. Slow flash FAULT indicator (refer to the detailed description in chapter keypad indicators)
2. When the fault is reset, the FAULT indicator is turned off when there is no other system
fault.
Configuration Conflict Keyfobs
Condition:
Any one keyfob configuration is error.
Restore:
All keyfob configuration are correct and fault is reset.
Supervise:
1. Slow flash FAULT indicator (refer to the detailed description in chapter keypad indicators)
2. When the fault is reset, the FAULT indicator is turned off when there is no other system
fault.
2 - Power Failure
The zone indicator 2 lights to indicate Power Faults. Enter [2] to step to Power Faults list for
more information.
– Panel AC Failure
Condition:
1. 18V AC supply deficiency to panel caused by transformer.
2. 220V power supply fuse broken.
3. 220V power supply disconnected.
Restore:
AC MAINS supply is reconnected and fault is reset.
1. Monitor the voltage by MPU.
2. If the AC fault is not restored in 1 hour after the fault occurred, report the fault to
configured destination on address 124.
3. Slow flash FAULT indicator (refer to the detailed description in chapter keypad indicators)
4. As the AC supply is reconnected, the MAINS indicator is back to light (except in
Programming Mode or Code Functions Mode ).
72
en | Settings
AMAX panel 4000 / AMAX panel 4000
EN
2013.07 | 03 | F.01U.267.112 Installation Guide Bosch Sicherheitsysteme GmbH
- Table of contents 3
- 4 en 4
- Table of Contents 5
- 6 en 6
- Graphics 7
- 8 en 8
- Short Information 9
- System overview 10
- Brief Introduction 11
- Address Setting 11
- Wiring and Installation 12
- Alarm Control Panel 13
- DIP Switch 16
- Status Indicator 16
- Installation 17
- Press latch 23
- Wall Tamper 24
- Address Jumper 26
- E N √ E N √ 29
- Backup Battery 30
- Installation 31
- Settings 32
- Receiver Subscriber ID Number 33
- Receiver Transmission Format 33
- 34 en 34
- Settings 35
- 36 en 36
- Settings 37
- Dual IP 38
- System Reporting 39
- Settings 41
- Settings 43
- 44 en 44
- Domestic Call 45
- Zone Inputs 46
- BBBBB7DPSHU6ZLWFK 47
- BBBBB=RQH6ZLWFK 47
- Settings 49
- Settings 51
- 52 en 52
- Settings 53
- Settings 55
- Adding and Changing Zone 57
- Onboard / Extension Output 58
- Output Events 58
- Settings 59
- Settings 61
- Output Options 63
- 64 en 64
- Settings 65
- 66 en 66
- Settings 69
- Settings 71
- Settings 73
- Settings 75
- Settings 77
- Common Area 78
- Area Delay 79
- Keypad Area 79
- Configuration 80
- User Code Commands 81
- LCD Keypad Menu Programming 82
- INSTALLER MENU 83
- COM+REPORT SETTING 84
- ZONE SETTING 85
- KP/AREA SETTING 86
- SYSTEM SETTING 87
- OUTPUT SETTING 88
- RF SETTING 89
- LED/LCD Keypad Programming 90
- PC Programming 91
- 92 en 92
- Direct Connection 93
- Figure 8.13: A-Link Plus 94
- Figure 8.14: Direct link port 94
- 94 en 94
- Modem Connection 95
- 96 en 96
- Configuration 97
- 98 en 98
- Figure 8.19: Modem Connect 99
- Configuration 99
- IP Connection 100
- Configuration 101
- 102 en 102
- Configuration 103
- Figure 8.23: Network Connect 104
- 104 en 104
- Configuration 105
- 106 en 106
- Programming 107
- 108 en 108
- Programming 109
- VDS-A EN=3 110
- VDS-A=0 110
- Programming 111
- 112 en 112
- Zone Programming 113
- 114 en 114
- Programming 115
- 116 en 116
- Programming 117
- 118 en 118
- Programming 119
- 120 en 120
- Programming 121
- 122 en 122
- Programming 123
- Output Programming 124
- Programming 125
- 126 en 126
- Programming 127
- 128 en 128
- Access Codes 129
- 130 en 130
- Programming 131
- 132 en 132
- Programming 133
- 134 en 134
- System Programming 135
- Programming 137
- 138 en 138
- Programming 139
- 140 en 140
- Programming 141
- 142 en 142
- Programming 143
- Programming 145
- 146 en 146
- Programming 147
- 148 en 148
- Table 9.6: Characters 149
- Programming 149
- 150 en 150
- Table 9.7: Assign Zone Names 151
- Programming 151
- 152 en 152
- Keypad Usage and Operations 153
- 1 2 3 … 157
- Arming the System 158
- Disarming the System 159
- 1 Accessory Module Failure 160
- Power Failure 160
- Bypassing Zones 163
- Change Individual Code 165
- Keypad Panic Alarm 165
- Keypad Fire Alarm 166
- Keypad Medical Alarm 166
- Troubleshooting 167
- 168 en 168
- Troubleshooting 169
- Maintenance12 170
- Technical Data 171
- 172 en 172
- Technical Data 173
- 174 en 174
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 4000 EN
(94 paginas)
(24 paginas)
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales