Bosch B450 Guía de instalación Pagina 102
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
You can program the Exit Timer from 0 to 255 sec in increments of 1 sec. When arming the
system in AWAY Mode, the remote codepad beeps during Exit Time until the final 10 sec, when
the codepad sounds one continuous beep to indicate the end of Exit Time is near.
The remote codepad always sounds one short beep at the end of Exit Time when arming in
STAY Mode1 or STAY Mode 2.
Entry Guard Timer for STAY Mode
Location 472 to 473
Location Default
Increments of 1 sec (0 sec to 15 sec) 472 0
Increments of 16 sec (0 sec to 240 sec) 473 0
Entry Guard Timer for STAY Mode is the delay time used for all zones except 24-Hour Burglary
and 24- Hour Fire Zones when the system is armed in STAY Mode 1 or STAY Mode 2. All zones,
including Delay Zones, use this timer for the entry delay (for example, the Entry Guard Timer
overrides the delay time programmed for a Delay Zone). If the Entry Guard Timer is
programmed as 0, each zone acts according to its programmed zone type.
Delay Alarm Reporting Time
Location 474 to 475
Location Default
Increments of 1 sec (0 sec to 15 sec) 474 0
Increments of 16 sec (0 sec to 240 sec) 475 0
These locations program the time in sec that a delayed report waits dormant in the buffer
before it is sent to the receiving party. If a User Code holder resets the alarm within this time
frame, the control panel clears the communicator buffer and does not report the alarm to the
receiving party.
Sensor Watch Time
Location 476 to 477
Location Default
Increments of 1 sec (0 sec to 15 sec) 476 0
Increments of 16 sec (0 sec to 240 sec) 477 0
The time set in these two locations determines the number of days (0 to 99) a zone can
remain sealed before registering as a fault. This feature is active only when the system is
disarmed. If a zone programmed for Sensor Watch is not unsealed and reset during this time,
the FAULT indicator lights.
10.5
10.6
10.7
102 en | System Event Timers Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch B450
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 4600 Series Manual de instrucciones
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 4000 EN Guía de instalación
(176 paginas)
(176 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8016/90 Manual de instrucciones
(24 paginas)
(24 paginas)
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales