Bosch B450 Guía de instalación Pagina 95
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
If this option is selected, the system can be armed with the zone unsealed. If this option is not
selected, the system does not allow the User Code holder to arm the system until the zone is
sealed or manually isolated. Refer to Isolating zones, page 56 for more information.
8 – Zone Restore Report
If this option is selected, the zone sends Restore Reports when the zone is restored. If this
option is not selected, the zone does not send Restore Reports when the zone is restored.
If a non-24-Hour zone is not restored when the system is disarmed, the system automatically
sends a Zone Restore Report for that zone. All 24-Hour zones send a Zone Restore Report only
when the zone is restored.
Zone Report Options
By default, a zone reports only to Receiver 1. The table below lists the reporting options for
the zone.
Option Description
0 No report required
1 Receiver 1
2 Receiver 2
4 Receiver 1 and Receiver 2
8 Receiver 2 only when Receiver 1 fails
Keyswitch Zone Options
The table below lists the options available to Keyswitch Zones. If you program a zone as a
keyswitch input (Zone Type 11), program the selected Keyswitch Zone options in the location
normally used for Zone Options 1.
Option Description
0 Latching arm and disarm in AWAY Mode
1 Latching arm in AWAY Mode
2 Latching disarm from AWAY Mode, STAY Mode1, or STAY Mode 2
4 Latching arm and disarm in STAY Mode 1
5 Latching arm in STAY Mode 1
6 Latching disarm from STAY Mode 1 or STAY Mode 2
8 Momentary arm and disarm in AWAY Mode
9 Momentary arm in AWAY Mode
10 Momentary disarm from AWAY Mode, STAY Mode1, or STAY Mode 2
12 Momentary arm and disarm in STAY Mode 1
13 Momentary arm in STAY Mode 1
14 Momentary disarm from STAY Mode 1 or STAY Mode 2
0 – Latching Arm and Disarm in AWAY Mode
The system is armed or disarmed from AWAY Mode when using the latching keyswitch input.
9.3.7
9.3.8
Control Panel Zone Information | en 95
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch B450
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 4600 Series Manual de instrucciones
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 4000 EN Guía de instalación
(176 paginas)
(176 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8016/90 Manual de instrucciones
(24 paginas)
(24 paginas)
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales