Bosch B450 Guía de instalación Pagina 135
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
This output operates when any zone programmed to be silent activates. The output is reset
when the Siren Run Time expires, an audible alarm is activated, or a valid User Code is
entered.
2,2 Alarm When in STAY Mode
This output operates when an audible alarm zone is activated when the system is armed in
STAY Mode 1 or STAY Mode 2. The output is reset when the system is disarmed. Silent alarm
will not trigger this event.
2,3 Alarm When in AWAY Mode
This output operates when an audible zone alarm is activated when the system is armed in
AWAY Mode. The output is reset when the system is disarmed. Silent alarm will not trigger this
event.
2,4 Mimic System Fault
This output operates when any system fault occurs. The output is reset when all system faults
are restored.
2,5 Fire Alarm Resetting
This output operates when a 24-Hour Fire Zone or codepad fire alarm is activated. The output
is reset when a valid User Code is entered or when Siren Run Time expires.
2,6 Fire Alarm Latching
This output operates when a 24-Hour Fire Zone or codepad fire alarm is activated and is reset
when a valid user code is entered in system disarmed state or before the siren time expires in
system armed state.
2,7 Fire Alarm Verification
This feature operates output one second later when a 24-Hour Fire Zone is activated before
Fire alarming or immediately operate output when a 24-Hour Fire Zone is activated after Fire
alarming and before Fire alarming reset. This output event can operate the output only when
the pulse count of the 24-Hour Fire Zone is no less than 2. The output is reset when this Fire
Zone is restored. If no fire zone is activated, this output event is the same with Output Event
0,7.
If the smoke detector trips, the voltage to the smoke detector is disconnected for 15 sec and
then reapplied. No alarm is registered.
2,8 Remote Control 1
This output operates output when using the master code function or A-Link software or
Smartphone App (RSC) to turn remote output 1 on. The output is reset when using the master
code function or A-Link software or Smartphone App (RSC) to manually turn remote output 1
off or automatically turn remote output 1 off when the ON time expires if output polarity is
from 3 to 6 or from 10 to 13.
2,9 Remote Control 2
This output operates output when using the master code function or A-Link software or
Smartphone App (RSC) to turn remote output 2 on. The output is reset when using the master
code function or A-Link software or Smartphone App (RSC) to manually turn remote output 2
off or automatically turn remote output 2 off when the ON time expires if output polarity is
from 3 to 6 or from 10 to 13.
2,10 Remote Control 3
This output operates output when using the master code function or A-Link software or
Smartphone App (RSC) to turn remote output 3 on. The output is reset when using the master
code function or A-Link software or Smartphone App (RSC) to manually turn remote output 3
off or automatically turn remote output 3 off when the ON time expires if output polarity is
from 3 to 6 or from 10 to 13.
2,11 Radio Control Output 1
Control Panel
Programmable Outputs | en 135
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch B450
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 4600 Series Manual de instrucciones
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 4000 EN Guía de instalación
(176 paginas)
(176 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8016/90 Manual de instrucciones
(24 paginas)
(24 paginas)
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales