Bosch B450 Guía de instalación Pagina 77
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Sequence Indicator On Event
1 ON, Zone 2, STAY Stay armed by User 2
2 OFF, Zone 1 Disarmed by User 1
3 Zone 4, AWAY Alarm in Zone 4
4 Zone 3, AWAY Alarm in Zone 3
5 ON, Zone 2, AWAY AWAY armed by User 2
Each event is indicated by a beep every 2 second and a lit indicator. You can also press [STAY]
key to review the last event.
After the last event, three beeps sound to indicate the end of playback. You can stop the
replay at any time by pressing [AWAY].
Notice!
If the system is armed in STAY Mode 1 or STAY Mode 2, the STAY indicator shows the event
memory playback. There is no differentiation between STAY Mode 1 and STAY Mode 2.
If the control panel is powered down, the memory of all events is saved.
User Code Functions
Arm or Disarm Both Areas at the Same Time
This User Code function operates only with partitioned systems and allows User Codes
allocated to both Area 1 and Area 2 to arm or disarm both areas at the same time.
This feature allows a user assigned to both areas to arm or disarm the system by pressing one
extra button on a partitioned codepad rather than entering a code on each partitioned
codepad. To enable this feature, select Option 2 in Location 501 (refer to Partitioning Options
2, page 111).
To arm or disarm both areas at the same time:
Enter your User Code and press [0][AWAY]. Two beeps sound and both areas are armed or
disarmed from AWAY Mode.
You can also arm/disarm both areas from a common codepad (assigned to both areas) with a
common user code (assigned to both areas).
Hold-Down Functions
Hold-down functions allow easy activation of specific operations. When you hold down a
button for 2 sec, two beeps sound and the corresponding function operates.
Arm the System in AWAY Mode
Holding down [#] until two beeps sound arms the system in AWAY Mode. This hold-down
function operates only if you select Option 2 in Location 497 (refer to Consumer Options 2,
page 109).
7.3
7.4
7.4.1
Control Panel System Functions | en 77
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch B450
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 4600 Series Manual de instrucciones
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 4000 EN Guía de instalación
(176 paginas)
(176 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8016/90 Manual de instrucciones
(24 paginas)
(24 paginas)
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales