Bosch B450 Guía de instalación Pagina 142
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Reports
Zone Tamper Report
A Zone Tamper Report (Contact ID Event Code144) is sent when Option 14 is programmed in
Location 266 and the zone loop using split EOL resistors (3K3/6K8) with tamper (1K)
becomes open circuit.
Walk Test Report
A Walk Test Report (Contact ID Event Code 607) is sent when either the Installer or Master
Code holder activates Walk Test Mode.
Bypass Report
A zone is bypassed when it is manually isolated. A Zone Bypass Report (Contact ID Event Code
573) is sent at the end of Exit Time for any zone that was manually isolated. A 24-Hour Zone
sends a Zone Bypass Report when the zone is selected to be isolated.
A Zone Bypass Restore Report is sent when the system is disarmed. All bypassed zones are
automatically cleared when the system is disarmed.
The Bypass code parameter has no effect on Contact ID Format because a Zone Bypass is
always reported as Event Code 573.
Notice!
A 24-Hour Fire Zone that is manually bypassed reports as Contact ID Event Code 571.
Other 24-Hour Zone that is manually bypassed reports as Contact ID Event Code 572.
Trouble Report
A zone is in trouble when it is unsealed at the end of Exit Time. A Sensor Trouble Report
(Contact ID Event Code 380) is sent to indicate that one or more zones were automatically
isolated by the system. 24- Hour Zones that are unsealed at the end of Exit Time do not
transmit a Sensor Trouble Report because the restoral for that zone is still outstanding.
A Sensor Trouble Restore Report is sent for Burglary Zones when the zone is resealed or the
next time the system is disarmed (whichever happens first). A 24- Hour Zone sends a restore
signal only when it is resealed.
The Trouble code parameter has no effect on Contact ID Format because a Sensor Trouble
Report is always reported as Event Code 380.
Sensor Watch Report
A Self Test Failure Report (Contact ID Event Code307) is sent to the base station receiver
when a zone was not activated during the Sensor Watch Time programmed in Locations 476
and 477 This report continues to be sent (according to the frequency of the Sensor Watch
Time) until the fault is corrected.
To clear the fault and stop any additional reporting, you must unseal and reseal the zone that
registered the fault. Use the Sensor Watch Time in Locations476 and 477 to set the number of
days a zone can remain sealed without registering a fault.
17
17.1
17.2
17.3
17.4
17.5
142 en | Reports Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch B450
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 4600 Series Manual de instrucciones
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 4000 EN Guía de instalación
(176 paginas)
(176 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8016/90 Manual de instrucciones
(24 paginas)
(24 paginas)
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales