Bosch B450 Guía de instalación Pagina 104
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
This location sets the time period during which the control panel warns you it is automatically
armed in AWAY Mode. The codepad beeps once every second until the Pre-Alert Timer expires:
the system then automatically arms itself in AWAY Mode. If you want the system to
automatically arm in STAY Mode 1, enable Option 4 in Location 496.
After the control panel is automatically armed in AWAY Mode or STAY Mode 1, Exit Time starts.
If a valid User Code is entered during the Pre-Alert Time, the Auto Arming Time programmed in
Locations 482 to 485 is extended by 1 hour.
If you want a programmable output to operate during the Auto Arming Pre-Alert Time, use
Output Event Type 0,5 Auto Arm Pre-Arming Alert Time.
Auto Arming Time
Location 482 to 485
Location Default
Hour of the day (tens digit) 482 0
Hour of the day (units digit) 483 0
Minute of the day (tens digit) 484 0
Minute of the day (units digit) 485 0
These locations specify the time of day the system automatically arms itself in AWAY Mode.
Set this time in 24-hour format (for example, program 10:30 PM as 2230). If you want the
system to arm in STAY Mode 1, select Option 4 in Location 496.
If forced arming is disabled for any zone, the automatic arming feature operates regardless of
whether any zones are unsealed.
User Code 997 is reported when this feature is used. For partitioned control panels, both
areas are automatically armed in AWAY Mode at the same time each day.
Auto Disarming Time
Location 486 to 489
Location Default
Hour of the day (tens digit) 486 0
Hour of the day (units digit) 487 0
Minute of the day (tens digit) 488 0
Minute of the day (units digit) 489 0
These locations specify the time of day the system automatically disarms itself. Set this time
in 24-hour format (for example, program 10:30 PM as 2230).
User Code 997 is reported when this feature is used. For partitioned control panels, both
areas are automatically disarmed at the same time each day.
10.12
10.13
104 en | System Event Timers Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch B450
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 4600 Series Manual de instrucciones
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 4000 EN Guía de instalación
(176 paginas)
(176 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8016/90 Manual de instrucciones
(24 paginas)
(24 paginas)
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales