Bosch B450 Guía de instalación Pagina 92
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
A Chime Zone is not a burglary zone. It can never sound the sirens or activate the
communication module. Its purpose is to map the zone to a programmable output to indicate
if the zone is sealed or unsealed.
Chime zones require EOL resistors and are registered at a remote codepad. These zones do
not affect the operation of forced arming.
15 –Zone Not Used
If a zone is not used, program the zone type location to 15. An EOL resistor is not required if
this zone type is used. This zone type never sounds the sirens or activates the communication
module.
Zone Pulse Count
Zone pulse count is the number of times a zone must be activated before the zone registers an
alarm. The number can vary from 0 to 15. The zone pulse count value is relative to the time
frame (that is, the number of pulses that must be present during a particular time frame).
Zone Pulse Count = 0, means the Zone Pulse Count function is disabled. Refer to Zone Pulse
Count Time, page 92 for more information.
Notice!
A zone that is programmed with a pulse count activates an alarm when it is continuously
unsealed for 10 sec. A 24- Hour Fire Zone programmed with a pulse count activates an alarm
when it is continuously unsealed for 30 sec.
Zone Pulse Count Handover
Zone pulse count handover operates only with Zone Pulse Count Time options 8 to 15.
Any zone that registers one active pulse automatically increments any other zone pulse count
that already registered at least one activate pulse during its respective time. To enable this
feature, select Option 4 in Location 494 (refer to System Options 3, page 107.
Notice!
24-Hour Zones will not receive all handover pulses from other zones. 24-Hour Zones can
handover pulses to other zones.
Zone Pulse Count Time
Zone pulse count time is the time frame or period over which the programmed number of
pulses must register to activate an alarm.
Zone Pulse Count Times
20 ms Option Loop Response Time
(sec)
150 ms Option Loop Response Time
(sec)
0 0.5 8 20
1 1 9 30
2 2 10 40
3 3 11 50
4 4 12 60
5 5 13 90
9.3.3
9.3.4
92 en | Zone Information Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch B450
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 4600 Series Manual de instrucciones
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 4000 EN Guía de instalación
(176 paginas)
(176 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8016/90 Manual de instrucciones
(24 paginas)
(24 paginas)
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales