Bosch B450 Guía de instalación Pagina 106
- Pagina / 152
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
System and Consumer Options
The locations in this section have up to four options. You can select any combination of these
options by programming a single value. Calculate this value by adding the option bit numbers
together.
System Options 1
Item Location Option Default New
System Options 1 0492 1 = Bosch Security Systems smart lockout
allowed
2 = Warning device monitor
4 = Strobe indication for radio arm/disarm
8 = Assign button 4 on transmitter to operate
STAY Mode 1
1
1 – Smart Lockout Allowed
This feature allows the control panel to remove any zones that are programmed for lockout
communicator from the lockout list when the sirens are running. This feature allows a
monitoring station to receive zone alarm reports from previously locked out zones during siren
time.
2 – Warning Device (Output1-3) Monitor
If this option is selected, the control panel detects when Output1-3 Event Type, programmed
as a Warning Device (Horn speaker, Siren Running, Strobe), is disconnected from the
terminals. The FAULT indicator lights when the Warning Device is disconnected and is
extinguished when the Warning Device is reconnected.
If an output is required to operate when the Warning Device is disconnected, use Output
Event Type 1,6 Warning Device Monitor Fail.
4 – Strobe Indications for Radio Arm/Disarm
This option allows the strobe to indicate when the system is armed and disarmed when
remotely operating the system using the RF Receiver.
Strobe Duration
System Status
3 sec System disarmed
6 sec System armed in AWAY Mode
6 sec System armed in STAY Mode 1
Table 11.1: Strobe Indications for Remote Operations
8 – Assign Button 4 on Trasmitter To Operate STAY Mode 1
This option allows Button 4 on the RFKF-FB Transmitter to arm the system in STAY Mode 1.
System Options 2
Item Location Option Default New
System Options 2 0493 1 = Codepad panic to be silent
2 = Codepad fire to be silent
4 = Codepad medical to be silent
8 = Access denied (code retries) to be silent
0
11
11.1
11.2
106 en | System and Consumer Options Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch B450
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 4600 Series Manual de instrucciones
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AMAX panel 4000 EN Guía de instalación
(176 paginas)
(176 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch LTC 8016/90 Manual de instrucciones
(24 paginas)
(24 paginas)
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales