Bosch DS7445i Guía de usuario descargar pdf (Pagina 30)

PART II: KEYPAD USER’S GUIDE: DS7445i LED KEYPAD

5.0 Using the DS7445i LED Keypad

The DS7445i LED Keypad can only display

Zones 1-16 or Users 1-16. Any functions that

require displaying zones or users higher than

16 cannot be performed from this keypad.

The DS7445i LED Keypad turns an LED (or series of

LEDs) ON or flashes an LED (or series of LEDs) to

indicate system events and conditions by.

= LED ON

= LED Flashing

See Table 4 on page 6 for DS7445i LED functions.

5.1 Silence Alarms

Description

When an alarm occurs, the alarm tone sounds and

the zone(s) in alarm illuminate on the display (up to

Zone 16).

If you enter your PIN before the abort timer

expires, the alarm report is aborted (non-fire

alarms only).

Procedure

1. Enter your PIN to silence an alarm and turn the

system off (if it was turned on). An alarm report is

sent if the alarm is not acknowledged in time.

2. Press and hold the [#] key to remove the alarms

(flashing zone numbers) from the keypad display.

See View Alarm Memory” on page 40 to see

which zones caused the alarm.

5.2 Keypad Adjust

I can perform this function.

I cannot perform this function.

Key Sequence: [#] + [4] + [9]

Description

Use this function to adjust the keypad’s sounder

volume (non-alarm tones).

1. Enter a valid user PIN.

2. Press [#] + [4] + [9].

3. To adjust the keypad’s sounder volume and non-

alarm tone volume, press and hold the [*] key,

and then press [1] to increase the volume or [4]

to decrease the volume.

4. Press the [#] key to save the setting and exit this

function.

5.3 Turn the System Off

Entry Delay Time (to be filled in by your Security

Company):

You have __________ seconds to enter the premises

and turn the system off.

Description

Turn the security system off by entering your PIN.

When the system is on, you must enter through a

designated Entry door to prevent an alarm. Opening a

designated door starts Entry Delay. During Entry

Delay time, the keypad emits a double tone every

second to remind you to turn the system off. Enter

your PIN before the Entry Delay time expires to turn

the system off.

If you enter through the wrong door or fail to turn the

system off before the Entry Delay time expires, you

may cause an alarm. If an alarm occurs, silence the

alarm by entering your PIN and call your Security

Company to let them know that it is not an emergency

situation.

Procedure

1. When the system is All On, the keypad’s Armed

LED is on. If the system is on Perimeter Only or

Partial On, the keypad’s Perimeter LED is on as

well.

Status

Power

Fire

Perimeter

Supervisory

Bell Silenced

Trouble

TEST WEEKLY

1 2 3 4 5 6 7 8

9 10

11 12

13 14

15 16

Armed

System is All On

Status

Fire

Supervisory

Bell Silenced

Trouble

TEST WEEKLY

1 2 3 4 5 6 7 8

9 10

11 12 13

14 15

Armed

System is Perimeter Only on or Partial On

Perimeter

Power

2. Enter your PIN to turn the system off. Once the

system is off, the keypad turns the Armed LED or

Perimeter LED off.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 53 54

Comentarios a estos manuales

Sin comentarios

Bosch DS7445i Guía de usuario Pagina 30

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch DS7445i