Bosch DS7445i Guía de usuario Pagina 37
- Pagina / 54
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
DS7240/DS7220 User's Guide Copyright 2002 Detection Systems, Inc. P/N: 49211C Page 37
PART II: KEYPAD USER’S GUIDE: DS7445i LED KEYPAD
On
Status
Power
Fire
Supervisory
Bell Silenced
Trouble
TEST WEEKLY
7 8
9 10
11 12 13
14 15 16
Armed Perimeter
Flashing Status LED
1 2 3 4 5 6
LED 2 On steady;
LEDs 1, 3-6 flash
If the user does not exist in the system as set
up by your Security Company, the keypad
emits an error tone.
6. Enter a new PIN with the same number of digits
as the old PIN. If the error tone sounds (four
quick beeps), try a different new PIN.
7. Enter the new PIN again for verification.
The available user numbers (including the one
just changed) flash. This indicates that you have
successfully changed the intended user’s PIN.
Repeat Steps 5 and 6 to change another PIN, or
press the [#] key twice to exit this function.
5.15 Change Others’ PIN Authority Levels
I can perform this function.
I cannot perform this function.
Key Sequence: [#] + [5] + [6]
Description
Use this function to change PIN authority levels for
each user in the system. This function requires the
appropriate authority level to change PINs.
You cannot change your own PIN authority level.
Only use this feature under the direction of your
Security Company.
Your Security Company should fill in the following:
• Authority Level 1 includes these functions:
• Authority Level 2 includes these functions:
• Authority Level 3 includes these functions:
• Authority Level 4 includes these functions:
Procedure
1. Make sure that the system is turned off (Armed
LED is off).
2. Enter a valid user PIN.
3. Enter [#] + [5] + [6].
Zone LEDs 1, 2 and 3 flash (Status LED
continues to flash).
On
Status
Power
Fire
Supervisory
Bell Silenced
Trouble
TEST WEEKLY
7 8
9 10
11 12 13 14
15 16
Armed Perimeter
Flashing Status LED
1 2 3 4 5 6
Flashing Zone LEDs
The flashing Zone LEDs represent the selections
you may make by pressing the corresponding
number key.
• 1: To change PINs, press [1].
• 2: To change PIN authority levels, press [2].
• 3: To assign an area to a PIN, press [3].
4. Press [2] to change PIN authority levels. The
available user numbers now flash (the example
below shows user numbers 1-6 as available
users). The Status LED continues to flash.
On
Status
Power
Fire
Supervisory
Bell Silenced
Trouble
TEST WEEKLY
7 8
9 10
11 12 13
14 15 16
Armed Perimeter
Flashing Status LED
1 2 3 4 5 6
Flashing LEDs indicate
available users
5. Enter the user number whose PIN authority level
you want to change followed by the [*] key. For
example, press [2] + [*] to change the PIN for
User 2. The “2” LED now stays on steady while
the other LEDs (including the Status LED) flash.
On
Status
Power
Fire
Supervisory
Bell Silenced
Trouble
TEST WEEKLY
7 8
9 10 11 12 13
14 15
16
Armed Perimeter
Flashing Status LED
1 2 3 4 5 6
LED on indicates selected user
Flashing LEDs indicate
other available users
If the user does not exist in the system as set
up by your Security Company, the keypad
emits an error tone.
6. Enter the new authority level (1-4) followed by the
[#] key.
The available user numbers (including the one
just changed) flash. This indicates that you have
successfully changed the intended user’s PIN
authority level.
Repeat Steps 5 and 6 to change another PIN
authority level, or press the [#] key twice to exit
this function.
- User’s Guide for the 1
- MY ALARM COMPANY IS: 2
- Contents 3
- Part I: Introduction 4
- 3.0 Keypad Overview 5
- 3.2 Keypad Tones 6
- 3.3 Keypad LED Functions 6
- 3.4 Function Key Sequences 7
- 3.5 System Events 7
- 3.8 Logging Out of the System 7
- Part II: Keypad User’s Guide 8
- 4.7 Set Partial On Zones 10
- 4.10 Force Arming the System 12
- 4.11 View Faulted Zones 13
- 4.12 Bypass Zones 13
- 4.13 Date and Time 14
- 4.14 Change PIN 14
- 4.15 Change Others’ PINs 15
- 4.17 Add a PIN 16
- 4.18 Delete a PIN 17
- 4.19 Renew One-Time PINs 17
- 4.20 Check System Troubles 18
- 4.21 View Alarm Memory 18
- 4.22 View System Trouble 19
- 4.23 View Zone Trouble 19
- 4.24 System Test 19
- 4.25 Walk Test 20
- 4.26 Reset the System 21
- 4.27 Turn Chime On/Off 21
- 4.28 Select Chime Tone 21
- 4.29 Select Chime Zones 22
- 4.30 Extend Auto-On Time 22
- 4.31 Change Skeds 22
- 4.32 Change Outputs 25
- 4.33 Remote Program 26
- 4.34 All Areas Off 26
- 4.35 All Areas On 26
- 4.36 Move to Area 27
- 4.37 Auto-Forward On Setup 27
- 4.38 Auto-Forward Off Setup 28
- 4.39 Auto-Forward On/Off 28
- 4.41 View Log 29
- 5.1 Silence Alarms 30
- 5.2 Keypad Adjust 30
- 5.3 Turn the System Off 30
- 5.4 Turn the System All On 31
- 5.7 Set Partial On Zones 32
- Flashing Armed LED 33
- 5.10 Force Arming the System 34
- 5.11 Bypass Zones 35
- 5.12 Date and Time 35
- I can perform this function 36
- 5.17 Delete a PIN 39
- 5.18 Renew One-Time PINs 39
- 5.19 Check System Troubles 40
- 5.20 View Alarm Memory 40
- 5.21 View System Trouble 40
- 5.22 View Zone Trouble 41
- 5.23 System Test 41
- 5.24 Walk Test 42
- 5.25 Reset the System 42
- 5.26 Turn Chime On/Off 42
- 5.29 Extend Auto On Time 44
- 5.30 All Areas On 44
- 5.31 All Areas Off 44
- 5.32 Auto Forward On/Off 44
- 5.34 Remote Program 45
- Part III: Reference Materials 46
- 7.0 Panel Event Descriptions 47
- 10.0 Maintenance and Service 52
- 11.0 Power Failure 52
- 12.0 How to Clean the Keypad 52
- 13.0 Glossary 53
- Detection Systems, Inc. 6/02 54
- P/N: 49211C Page 54 of 54 54
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Bosch DS7445i
(44 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch APC-AMC2-4WCF Manual de instalación
(62 paginas)
(62 paginas)
Los Sistemas De Control De Acceso De Seguridad Bosch AutoDome 600 Series Manual de usuario
(11 paginas)
(11 paginas)
(8 paginas)
(64 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales